基于labview的宠物连连看

使用EMD对采集数据进行数据模态分解，得到各个分量信号(Use EMD to cEMD data)

本文通过运用myDAQ搭建一个在线音效处理系统，利用LabVIEW控制myDAQ完成信号的采集、分析以及发生。 (By using myDAQ build an online audio processing system, using the LabVIEW Control myDAQ complete signal acquisition, analysis, and happen.)

该程序适用于示波器数据采集，用labview写的，适用于安捷伦得示波器（后面凑字，该程序适用于示波器数据采集，用labview写的，适用于安捷伦得示波器）

基于LabvIEw的通用自动测试系统(ATs)舍计算机，可鳊程激励、响应数据采集及uuT模块，采用MxI总线控制方式。专用信号发生器为uuT提供模拟激励信号，矩阵开关和适配器完成不同信号间切换。主控计算机执行测试程序，信号发生器发送激励信号，数据采集卡采集数据，采集数据经调理后，并与标准数据|匕较是否满足相应测试结果。(The general automatic test system (ATs) based on LabvIEw can be used as a computer to excite, respond to data acquisition and uuT module. The control mode of MxI bus is adopted. Special signal generator provides analog excitation signal for uuT, matrix switch and adapter complete switching between different signals. The main control computer executes the test program, the signal generator sends the excitation signal, the data acquisition card collects the data, after the data acquisition is adjusted, and compares with the standard data | dagger whether it meets the corresponding test results.)

此程序是基于labview的tcp/ip控件设计的多功能聊天软件，类QQ，可以进行文本、图片、文件等传输，可以在局域网、广域网内进行传输，具有很好的适用性，可以进行课程设计或毕业设计(This procedure is based on the labview tcp/ip control design versatility chat software, classes QQ, can be text, images, documents, etc. transfer, can be transmitted within a LAN, WAN, with good applicability and can be curriculum design or graduation)

用于测量信号的振幅谱与功率谱，对初学LABVIEW做信号分析会有帮助。(Used to measure the signal amplitude spectrum and the power spectrum, signal analysis for beginners LABVIEW do help.)

labview模糊控制器的学习 labview模糊控制器的学习 labview模糊控制器的学习 labview模糊控制器的学习 labview模糊控制器的学习 labview模糊控制器的学习 labview模糊控制器的学习 labview模糊控制器的学习 labview模糊控制器的学习 labview模糊控制器的学习 labview模糊控制器的学习 labview模糊控制器的学习 labview模糊控制器的学习 labview模糊控制器的学习 labview模糊控制器的学习

说明：  通过labview实现tcp协议的通信，可以使用虚拟串口和电脑通信(The communication of TCP protocol can be realized by labview. Virtual serial port and computer communication can be used.)

说明：  通过labview实现通信信道仿真中的信道估计以及时域均衡，注意这个是以及完整实现了信道的搭建，通过添加时域均衡以及信道估计实现最终的仿真(The channel estimation and time-domain equalization in communication channel simulation are realized by labview. Note that this is to build the channel completely. The final simulation is achieved by adding time-domain equalization and channel estimation.)

利用LabVIEW的Active X模块以及STK的Connect 模块实现两种软件交互的方法，通过LabVIEW 的Active X功能连接STK，利用Connect模块中的指令驱动STK产生卫星的相关数据，最终将有关数据返回至Lab VIEW中并显示出来，实现了Lab VIEW与STK的无缝连接(Design of a Satellite Orbit Prediction Visualization Platform Based on Lab VIEW and STK A method of designing a satellite orbit prediction visualization platform based on a hardware-in-loop validated simulation system of small satellite is introduced． Satellite Tool Kit is an analysis software widely used in simulating orbit system for satellite ， but STK can’t accomplish the relevant function that acquired by the hardware- in-loop validated simulation system mentioned． Based on this requirement ， a method of using Active X technology in Lab VIEW and STK/Connect module to interact the two kinds software is introduced． Through calling STK and u- sing Connect module in STK to obtain the relevant data ， finally all the datas in need within a window synchronously can be displaied ， which realized the connection between Lab VIEW and STK ， also accomplished the relevant func- tion and has a applied value． )