51单片机驱动针式打印头的程序

1、有单，和单双两种旋转模式。2、可以选择置数、和连续。两种控制模式。3、按梯形 曲线加速和减速。 4、所有的置数，及速度，都能通过数字显示。 -one, single, and both single-and double-rotation mode. 2, we can choose a few home, and continuous. Two control mode. 3, trapezoid curve acceleration and deceleration. 4, all the home number, and speed, can be settled through figures show.

基于NRF905无线收发模块的无线按键程序-NRF905 wireless transceiver module based on the wireless key procedures

基于单片机8051的嵌入式开发指南主要是rty51和UCOS操作系统的开发.-Based on the 8051 single-chip embedded development guide primarily uCOS rty51 and operating system development.

三相步进电机的三相六拍工作方式，正转的绕组通电顺序：A、AB、B、BC、C、CA、A，反转的通电顺序：A、AC、C、CB、B、BA、B、A。 由于步进电机转子有一定的惯性以及所带负载的惯性，故步进电机的工作过程中不能及时的启动和停止，在启动时应慢慢的加速到预定速度，在停止前应逐渐减速到停止，否则，将产生失步现象。 步进电机的控制问题可总结为两点： 1、产生工作方式需要的时序脉冲； 2、控制步进电机的速度，使它始终遵循加速、匀速、减速的规律工作。 -Three-phase three-phase stepper motor six shot work, is to order the winding power: A, AB, B, BC, C, CA, A, reverse the order of power: A, AC, C, CB, B, BA, B, A. As the stepper motor rotor has a certain degree of inertia, as well as brought about by the inertia load, the stepper motor during the course of work should not start and stop time, start to be slowly accelerated to a predetermined speed, the stop should be to slow down gradually to the stop, otherwise, will result in out-of-step phenomenon. Stepper motor control problems can be summarized in two points: one, resulting in the need to work the timing pulse 2, control the speed of stepper motor, so that it always followed acceleration, velocity, deceleration of the law of the work.

DS1302+DS18B20+LCD1602在51系统上的实时时钟-DS1302+ DS18B20+ LCD1602 system in 51 real-time clock

这是一个msp430程序，是用于2个msp430f149单片机之间进行串口通信，程序已经调试好了，非常好用-This is a MSP430 procedure is used for two MSP430F149 single-chip serial communication between, the program has debug Well, very easy to use

8051两个单片机的通信，各自分别控制另一个单片机的跑马灯的左右跑动方向。keic工程文件-8051 2 MCU communication, each one separately control the left and right SCM ticker running direction. keic project file

这是常用的pic单片机子程序, 包括BCD码的转化和串行通讯等是PIC初学者理想的学习样板-This is the common pic microcontroller subroutine, including BCD conversion and serial communications beginners PIC is an ideal learning model

想学AVR的同学进来吧，好东东哦，你需要准备好如下的软、硬件 1. WinAVR 20050214 版本 2. AVR Studio 4.12 3. STK500 下载(烧录器)器 4. ATmega16 芯片及常用零件若干-Students want to learn AVR Come, good Dongdong Oh, you need to ready the following hardware and software 1. WinAVR 20050214 version 2. AVR Studio 4.12 3. STK500 download (burner) browser 4. ATmega16 chip and a number of commonly used parts

用凌阳单片机控制显示电压步进，增减，并输出模拟电压