-
XRDIn015GaNv6
Code to simulate 2theta-omega scans for InGaN/GaN films
- 2012-09-25 02:01:48下载
- 积分:1
-
mat
ecg signal implementation in matlab
- 2015-01-08 14:47:21下载
- 积分:1
-
new_hdpower
this paper presents new method for power flow
- 2015-01-31 16:49:58下载
- 积分:1
-
EKF_IMUKK
基于IMU的四元扩展卡尔曼滤波程序,主要用于姿态更新和数据融合(Quaternary-based IMU EKF program, mainly for the attitude update and data fusion)
- 2015-03-09 21:52:54下载
- 积分:1
-
矩量法计算长直线导体电容的计算matlab程序
矩量法计算长直线导体电容的计算matlab程序(Moment Method Calculation of long straight conductor capacitance calculation matlab program)
- 2007-12-09 13:35:05下载
- 积分:1
-
featureSelection
利用保留交叉验证(hold-out)的特征选择,有筛选排序的功能,并最终可以输出对应特征下标。(The use of cross-validation reserved (hold-out) feature selection, there is sort of filtering function, and eventually you can output the corresponding feature subscript.)
- 2013-08-11 10:26:17下载
- 积分:1
-
fdtd1D
Taflove书的一维时域有限差分完美边界的程序!欢迎下载!(Taflove book one-dimensional finite-difference time-domain boundary perfect program! Welcome to download!)
- 2013-12-16 12:39:13下载
- 积分:1
-
guangpu
主成分分析法,主要用在光谱处理上的,包括可见和近红外光谱,对于其他的一些统计学数据也比较适用,包括原数据和处理后的数据(Principal component analysis (pca), mainly used on spectrum processing, including visible and near infrared spectrum, and is also applicable for other statistical data)
- 2015-10-27 20:02:13下载
- 积分:1
-
wind
风机和水轮机互补发电模型,互补之后到达输出总功率一定。(Wind turbine and turbine complementary power generation model, after the arrival of the output power of each complementary.)
- 2016-05-26 11:52:48下载
- 积分:1
-
PID
一个比较典型的PID处理程序,在使用单片机作为控制cpu时,请稍作简化,具体的PID
参数必须由具体对象通过实验确定。由于单片机的处理速度和ram资源的限制,一般不采用浮点数运算,
而将所有参数全部用整数,运算到最后再除以一个2的N次方数据(相当于移位),作类似定点数运算,可
大大提高运算速度,根据控制精度的不同要求,当精度要求很高时,注意保留移位引起的“余数”,做好余
数补偿。这个程序只是一般常用pid算法的基本架构,没有包含输入输出处理部分。
(A typical PID process, using the microcontroller as a control cpu, make some simplification, the specific PID parameters must be determined experimentally by a specific object. As the chip processing speed and ram resource constraints, generally do not use floating-point operations, and all parameters of all integers, and divided by an operator to the last N-th power of 2 data (the equivalent of the shift) for a similar fixed-point operations, can greatly improve the speed of operation, according to the different requirements of precision control, when high precision, attention to retain the shift caused by the " remainder" and on the remainder of compensation. This procedure is commonly used basic structure pid algorithm, does not include input and output processing section.)
- 2011-07-17 23:45:45下载
- 积分:1