SeismicLab

for high precision wind energy conversion sysytems this fuzzy controller can be used

implementation of classification based on least square error method in MATLAB environment.

说明：  数学建模中的程序编写，矢量数据的显示，达到建模过程中用户的需求(Programming in the mathematical modeling and display of vector data, to the needs of users in the modeling process)

用Baum-Welch算法来迭代估计一个隐马尔科夫模型（HMM）的初始状态概率分布以及其状态转移概率矩阵。其中文件有mainfile_B_W.m为主函数，Baum_Welch.m为Baum-Welch算法迭代函数，Forward_variable.m与Backward_variable.m与Gamma_variable.m与Ksi_variable.m是需要计算的四种因子，B_pdf.m为混淆散射概率密度函数。(It s Baum-Welch algorithm for iteratively estimating the initial states probability distribution and state transition probability matrix. In the folder, "mainfile_B_W.m" is the main function, and "Baum_Welch.m" is the iteration Baum-Welch function. Also these four file "Forward_variable.m " "Backward_variable.m" "Gamma_variable.m" "Ksi_variable.m" are used for calculating crucial factors. "B_pdf.m" is the emission probability distrubution function.)

2*4 mimo系统的误码率测量。经过rayleigh信道(ber of 2*4 mimo)

说明：  自己翻译的一篇最新外文文献《使用无需重建最佳探测器的宽带压缩传感认知无线电》(Own translation of a the latest foreign literature use without having to rebuild the best detectors broadband compressed sensing cognitive radio &quot )

找出数据的规律，然后按照要求，对数据进行分类，使数据清晰明了 (Find out the rules of data, and then follow the requirements of the data classification, so that the data clarity)

说明：  任务：设计一个4×2.5Gbit/s 长距离光纤传输系统，并利用OptiSystem 仿真验证。 要求： 1．采用波分复用技术，波长设置以100GHz 为间隔，频率分别为193.1THz、193.2THz、193.3THz、193.4THz，每个波长传输速率为2.5Gbit/s（NRZ），传输距离为300km。采用常规光纤，光纤损耗系数为0.25dB/km。 2．单通道光发送机最大输出功率为0dBm，光接收机的接收光功率不低于－26dBm，过载点为－10dBm。 3．可以采用EDFA 作为线路放大器，其中EDFA 的输入功率限制在－18～2dBm，最大输出功率20dBm，增益范围为13～25dB，噪声指数4.0dB。(Task: Design a 4 x 2.5 Gbit/s long-distance optical fiber transmission system, and use OptiSystem simulation to verify. Requirement: 1. Using wavelength division multiplexing technology, the wavelength is set at 100GHz intervals, with frequencies of 193.1 THz, 193.2 THz, 193.3 THz and 193.4 THz, respectively. The transmission rate of each wavelength is 2.5 Gbit/s (NRZ), and the transmission distance is 300 km. The loss coefficient of conventional optical fibers is 0.25dB/km. 2. The maximum output power of a single-channel optical transmitter is 0 dBm, and the receiving power of an optical receiver is not less than -26 dBm, and the overload point is -10 dBm. 3. EDFA can be used as line amplifier, where the input power of EDFA is limited to - 18-2dBm, the maximum output power is 20dBm, the gain range is 13-25dB, and the noise index is 4.0dB.)

这是用matlab编写的支持向量机的函数工具箱，初学者可作参考(This is prepared by using matlab function Support Vector Machine Toolbox, beginners can make reference to)

一本介绍matlab的书籍，由西安交通大学李人厚编著(An introductory books matlab, from Xi an Jiaotong University, edited by Li Renhou)