Java-Bluetooth-API-2

华为短信网关资料，可直接去华为官网上下载。(Huawei SMS gateway information can be downloaded directly to Huawei' s official website.)

Zigbee Home Automation Webinar

RFID连接Arduino然后用串口监视显示测得数据(How to use RFID connect to Arduino.Then use serial monitor show the detected data in PC.)

使用到的参数跟谈到弹性网络的那一章里头所讲的是一样的， ke 则是终止条件。如果 step 被打勾，则程式在每一步之间会暂停 100毫秒（或其他使用者输入的数值）。如果 Random 被打勾，则程式会以系统时间作为乱数产生器的种子数，否则，就以使用者输入的数（ Random 右边那一格）为种子数。 你可以利用 load 来载入推销员问题档与其最佳解，如此便可比较弹性网络所找出来的解与最佳解差了多少。 Central, Radius, and Error 这三个参数的前两个，只影响弹性网络的起使位置和大小，对求解没有影响。第三个参数代表城市与网络点之间的容忍距离，也就是说，如果某城市与某网络点之间的距离，小于容忍距离，那就把这个城市当成是被该网络点所拜访。 按下小 w按钮会将目前的结果与参数值写到“en.out”这个档案。使得我们可以很方便地来比较不同参数的效果。 (use to turn the parameters of the network flexibility chapter Erlitou have said are the same, ke is the termination conditions. If the step was ticking, every step of the program will be suspended between one hundred milliseconds (or other user input value). If Random was ticking, the program will be the system time as the Random Number Generator the seeds, otherwise, Take the user input (which Random right field) for seeds. You can use load to stall contained salesman problem with the optimal solution, so can be more flexible network to find the best solution and the deficit with a number of questions. Central, Radius, and Error these three parameters of the former two, flexible network affects only the starting position and size so that the solution will not be affected. The third parame)

java程序员上班那点事儿自己看过还可以的书免费跟大家共享(java programmer at work that point Shier his book can also be seen free of charge with the share)

基于F2812的维也纳VIENNA电源程序。本程序根据三电平六开关（Vienna）整流器的工作模态，结合两电平空间矢量（SVPWM）的工作原理，介绍了Vienna整流器SVPWM控制采用两电平SVPWM控制等效的方法。本文提出了一种适用于各种负载条件下的中点电位控制算法。(Based F2812 Vienna VIENNA power program. This procedure based on three-level six-switch (Vienna) rectifier operational modal, combined with the two-level space vector (SVPWM) works, describes the Vienna rectifier SVPWM control method uses two-level SVPWM control equivalent. This paper presents a suitable under various load conditions midpoint potential control algorithm. )

一个双馈风力发电机的PSCAD案例，在官网的基础上有一些改进~(A doubly-fed wind power generator PSCAD case, on the basis of the website have some improvement ~)

串行端口的数字输出控制，本程序使用两个按钮使得用户通过按钮控制DTR和RTS的引脚电压。(Serial port of the digital output control, the program allows users to use two buttons through the button control DTR and RTS pin voltage.)

OpenCV-2.2-nov4l1.patch due to registration forms

Multimeter in pic18f4550 build in mikroC