登录
首页 » matlab » 潮流计算高斯法

潮流计算高斯法

于 2020-06-06 发布
0 324
下载积分: 1 下载次数: 2

代码说明:

说明:  可以对电力系统进行潮流计算,潮流计算所用方法为高斯赛德法。(Power flow calculation of power system using Gauss said method)

文件列表:

潮流计算高斯法\gaosifa.m, 1840 , 2019-06-09
潮流计算高斯法\homework.m, 1942 , 2019-06-09
潮流计算高斯法, 0 , 2020-06-06

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • harmonic
    说明:  利用Blackman窗函数对工频信号进行加窗FFT后校正计算出基波和谐波的幅值、频率和初始相角。(Blackman window function using frequency signal windowed FFT is calculated after the correction of fundamental and harmonic amplitude, frequency and initial phase angle.)
    2011-03-03 10:18:53下载
    积分:1
  • POA
    水库调度 单库POA,以乌江梯级水库群中单库东风为例(The reservoir scheduling single library POA)
    2012-07-28 10:04:47下载
    积分:1
  • re
    说明:  simulink搭建的全桥整流+buck电路,实现AC到DC,然后DC到DC的变换,其中全桥为SPWM控制。(Simulink built a full bridge rectifier +buck circuit, AC to DC, and then DC to DC transform, in which the whole bridge is SPWM control.)
    2020-11-27 21:09:30下载
    积分:1
  • mppt
    说明:  在局部阴影下实现光伏板的多峰mppt。运用模糊控制打的方法得到理想的输出特性曲线。(Multi-peak MPPT of photovoltaic panel is realized under local shadow.Using the method of fuzzy control to get the ideal output characteristic curve.)
    2019-03-09 16:08:45下载
    积分:1
  • 网粒子群优化算法
    说明:  微网粒子群优化配置程序,风光储设备选型及容量配置(Microgrid particle swarm optimization configuration program)
    2021-04-21 10:48:49下载
    积分:1
  • Matlab直流潮流程序
    电力系统直流潮流算法,利用matlab软件实现的直流潮流算法。(Calculation of DC power flow in power system)
    2018-05-02 10:09:35下载
    积分:1
  • MATP
    一种实现永磁同步电机的弱磁控制方式,在simulink进行了仿真。(Weak magnetic control of permanent magnet synchronous motor)
    2018-03-01 10:23:19下载
    积分:1
  • xingbotiqu
    说明:  里面通过MATALB中的simulink进行保护的构建,并利用编程的方法进行继电保护的构建(It uses Simulink in MATALB to construct the protection, and uses the programming method to construct the relay protection)
    2021-04-19 09:46:00下载
    积分:1
  • hydraulic_pitch_calculation
    液压变桨系统机构出力和载荷仿真仿真,能够核算不同配置和设计参数下的液压变桨系统性能和载荷假定结果的符合程度。(hydraulic pitch system design)
    2018-10-03 20:22:05下载
    积分:1
  • 级联故障下的潮流计算
    说明:  用牛顿法计算电力系统在级联故障下的潮流,对越限支路进行切除负荷。(Newton method is used to calculate the power flow of the power system under cascaded fault, and the load is cut off for the out of limit branch.)
    2020-06-06 12:41:02下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载