OOK

文档中包含TCA（迁移学习算法当中的迁移成分分析程序），包括原版和翻译版，复制到MATLAB上面可以很好的实现它的功能(Document contains TCA (migration learning algorithm among migration component analysis program), including the original and translation version, copied to MATLAB above, you can very well achieve its function)

说明：  欧 姆 龙 U D P 通 讯(Omron UDP communication)

求两条直线段的交点坐标的算法说明,是网上资料的经典积累-Seeking two coordinates of line segment intersection algorithm description

这是关于雷达杂波的仿真的matlab程序，希望对大家有所帮助-This is on the radar clutter of the Matlab simulation procedures, we hope to help

天文惯性组合导航软件仿真程序，供参考。(Software simulation program for astronomical inertial integrated navigation)

问题描述: 一杯沸水冷却，圆柱体模型，底面半径0.05m，高0.1m，周围温度20度，初始水温100度 方程是四维输运方程（常数a^2=k/(c*p)，k是热传导系数0.6006焦/（米*秒*度）） 初始条件：t=0时水等于100度 边界条件：1.上下壁都是自由冷却，第三类边界条件，周围温度保持在20度（H=k/h,h取1） 2.杯壁绝热，第二类边界条件 图形显示格式,取过圆柱轴的截面温度变化将其做成动画. -Problem description : a cup of boiling water cooling cylinder model, the bottom radius of 0.05m, 0.1m high. temperature around 20 degrees, initial temperature of 100 degrees equation is four-dimensional equations (a constant ^ 2 = k/(c* p), k is the thermal conductivity coefficient of 0.6006 Coke/(m** seconds degrees)) initial conditions : t = 0 to 100 degree water boundary conditions : 1. upper and lower walls are free cooling, the third boundary conditions, maintain the temperature around 20 degrees (H = k/h, h for 1) 2. Beibi insulation, The second category boundary conditions graphics format, cylindrical shaft for the cross section of its temperature changes caused animation.

说明：  STC89S52单片机设计一款智能充电器的控制系统，通过对电压传感器和电流传感器的检测，当检测充电电压和电流大设置值时，自动断开充电电路。本设计由软件和硬件两部分组成，硬件设计对单片机最小系统、电压电流采集电路、充电控制电路、按键电路、液晶显示电路、报警电路等进行设计，使控制器具备电压、电流检测，系统参数显示，自动断电控制等功能；软件设计方面对控制器的软件驱动程序进行设计。并利用Protues软件进行可行性仿真，对软件和硬件设计进行验证(425/5000 STC89S52 mcu design a smart charger control system, through the voltage sensor and current sensor detection, when the detection charging voltage and current settings, automatically open the charging circuit. This design is composed of two parts: software and hardware. The hardware design designs the minimum system, voltage and current collection circuit, charging control circuit, key-press circuit, liquid crystal display circuit, alarm circuit, etc. , the controller has the functions of voltage and current detection, system parameter display, automatic power-off control and so on. The feasibility simulation is carried out by using Protues software to verify the design of software and hardware)

图像显示窗口，可以打开图片，放大缩小图片，拖动图片。加载相机图片(Image display window, you can open the picture, zoom in and zoom out the picture, drag the picture. Loading Camera Pictures)

LBM方法介绍及编程；LBM模型分析及应用(Introduction and programming of LBM method)

TLC2543的中文简介,附有汇编操作,TLC2543是德州仪器公司生产的12位开关电容型逐次逼近模数转换器，它具有三个控制输入端，采用简单的3线SPI串行接口可方便地与微机进行连接，是12位数据采集系统的最佳选择器件之一。本文介绍了该芯片的功能、时序，并给出了8051单片机的接口电路。(TLC2543 briefed the Chinese, with the compilation operation, TLC2543 is by TI Switched-Capacitor 12-successive approximation ADC. it has three control input, a simple three-wire SPI serial interface can be easily connected with the computer, yes 12 Data Acquisition System devices to choose the best one. This paper introduces the chip functional, timing, and gives the 8051 interface circuit.)