登录
首页 » C51 » STC单片机多机联级串口程序可实现.416路控制

STC单片机多机联级串口程序可实现.416路控制

于 2020-03-06 发布
0 392
下载积分: 1 下载次数: 1

代码说明:

说明:  STC单片机多机连级串口程序可实现.416路控制. 串口和485都可以使用、 一个程序可以用在26块控制板上,通过拔码开关给板子编号,每块板可以过滤分析所接收到不同的代码。进行继电器的动作,能返回数据,因使用定时器发送返回,不会阻塞或者代码错乱、可以 用在中控,物联网,等各种控制场合。修改代码后,能达到上千路的控制。(STC single-chip microcomputer multi-level serial port program can realize 416 channel control. Serial port and 485 can be used. One program can be used on 26 control boards. Each board can filter and analyze different codes received by numbering the boards with the pull-out switch. Relay operation can return data, because the timer is used to send the return, it will not block or code confusion, and can be used in central control, Internet of things, and other control occasions. After modifying the code, it can achieve thousands of control.)

文件列表:

STC单片机多机联级串口程序可实现.416路控制.txt, 8426 , 2020-03-06

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 射线追踪法
    说明:  大气波导下,电磁波射频追踪研究,利用Matlab进行仿真(Radio Frequency Tracking of Electromagnetic Waves in Atmospheric Waveguide)
    2021-01-06 19:58:53下载
    积分:1
  • 语音处理,改变声调、语速等,matlab代码
    说明:  语音处理 改变声速变速不变调 改变声调不变速(Speech Processing Variable Speed Modification)
    2019-05-31 17:44:30下载
    积分:1
  • IIR 数字滤波器的设计与实现
    设计一个巴特沃兹数字低通滤波器,其技术指标为:3dB带宽为0.2π,阻带截止频率为0.3π,通带纹波为1dB,阻带衰减大于30dB,采样间隔T=10ms。 1)采用冲激响应不变法; 2)采用双线性变换法设计; 3)采用FIR的窗函数(Hanning窗、Hamming窗或Blackman窗)设计。(A Butterworth digital low-pass filter is designed. Its technical specifications are: 3 dB bandwidth is 0.2 pi, stopband cut-off frequency is 0.3 pi, passband ripple is 1 dB, stopband attenuation is more than 30 dB, sampling interval T=10 Ms. 1) Impulse response invariance method is adopted. 2) Design by bilinear transformation method; 3) FIR window function (Hanning window, Hamming window or Blackman window) is used to design.)
    2019-04-19 10:03:16下载
    积分:1
  • 40362 101 RTU32N
    说明:  Data-Sheet_03-11-2017
    2020-03-10 03:58:31下载
    积分:1
  • Vehicular_AdHoc_Networks_Simulation-master
    说明:  一个基于python 的V2V仿真代码。(the code is about V2V communication simulation)
    2020-12-13 15:39:15下载
    积分:1
  • cordic
    说明:  实现可连续输入数据做三角函数变换处理,通过verilog代码实现,(It realizes triangular function transformation for continuous input data.)
    2020-06-21 22:40:01下载
    积分:1
  • asd
    航空航天通信技术一般采用模拟通信的频率调制和数字通信的移相键控调制方法。这有利于充分应用信道带宽和能源。频率调制是在一定程度上改变载波或副载波的频率来传输信息的调制方法。移相键控调制是利用载波或副载波的相位跳变来传输信息的调制方法。移相键控又分二相移相键控、四相移相键控和多相移相键控,其中以四相移相键控和八相移相键控调制方法的效率较高(Aerospace communications technology commonly used analog communication of frequency modulation and the digital communication phase shift keying modulation method. This is helpful for making full use of channel bandwidth and energy. Frequency modulation is changed to some extent carrier or subcarrier frequency to transmit information modulation method. Phase shift keying modulation is the use of carrier or subcarrier phase jump to transmit information modulation method. Phase shift keying and binary phase shift keying, four phase shift keying and multiple phase shift keying, of which four phase shift keying and eight phase shift keying modulation method of high efficiency )
    2011-07-13 11:21:08下载
    积分:1
  • 用VHDL语言在CPLD_FPGA上实现浮点运算
    说明:  用VHDL语言在CPLD/FPGA上实现浮点运算的方法(in VHDL CPLD/FPGA achieve floating-point computation methods)
    2005-12-23 13:05:42下载
    积分:1
  • unam701
    生成2KHz和8KHz的混合信号,使该信号通过上述滤波器,观察滤波前后的波形变化和频谱分布情况,(The mixed signal of 2KHz and 8KHz is generated, and the waveform changes and spectrum distribution before and after filtering are observed through the filter.)
    2018-08-04 22:31:45下载
    积分:1
  • path loss
    无线信道建模,路径损耗及正态阴影模型源代码,可出图,(Path loss Wireless channel modeling)
    2019-05-07 17:39:48下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载