037_RPLY

说明：  电力系统最小二乘法状态估计模型 状态估计(Power System Least Squares State Estimation Model)

轨道根数与位置速度互化,对于初学轨道知识的人有一定的用处。(Orbital velocity and position of each of, for beginners who have some knowledge of the track usefulness.)

说明：  3DEC用户手册(4.0)中文版(3DEC4.0 manual with cover)

升压斩波电路（Boost）的仿真 针对 Boost 变换电路，完成以下工作： （1） 在 MATLAB/SIMULINK 下搭建 Buck 电路仿真模型，并设置好各个模块的参数； （2） 分别选择 3 个不同的占空比，用示波器同时观察 E，uGE，i1，io，uo 以及电感两 端的电压 uL和流过电容的电流 iL的波形（注意频率的选择）。(Boost simulation model is built under MATLAB / SIMULINK, and the parameters of each module are set up. (2) Choose three different duty cycles and simultaneously observe E, uGE, i1, io, uo and inductance with an oscilloscope. Voltage UL at End and Current iL Waveform through Capacitor (Attention to Frequency Selection)

说明：  提出了一套基于供电网格优化划分的中压配电网规划思路和方法。首先，确定规划区域主干通道布局，确保土地资源预留。然后，在明确网格划分目的和原则的基础上，基于就近选择负荷备供变电站和负荷聚类方法，实现供电网格在全局范围内的优化划分。最后，分别在各供电网格内，基于其供区分类优选接线模式和一、二次建设改造标准，并进行主干线布线规划。(This paper presents a set of ideas and methods for medium voltage distribution network planning based on power grid optimization. Firstly, the layout of the main corridors in the planning area is determined to ensure the reservation of land resources. Then, on the basis of defining the purpose and principle of grid partition, the optimal partition of power supply grid in the global scope is realized based on the near selection of load standby substation and load clustering method. Finally, in each power supply grid, based on the classification of supply areas, the optimal wiring mode and reconstruction standards of primary and secondary construction are selected, and the main wiring planning is carried out.)

比幅单脉冲测角, 雷达信号处理中常用测角方法(Amplitude comparison monopulse angle measurement,angle measuring method for radar)

说明：  元胞自动机（ CA ）是一种用来仿真局部规则和局部联系的方法。典型的元 胞自动机是定义在网格上的，每一个点上的网格代表一个元胞与一种有限的状 态。变化规则适用于每一个元胞并且同时进行。典型的变化规则，决定于元胞的 状态，以及其（ 4 或8 ）邻居的状态。元胞自动机已被应用于物理模拟，生物 模拟等领域。本文就一些有趣的规则，考虑如何编写有效的MATLAB 的程序来 实现这些元胞自动机。(Cellular automata (CA) is a method to simulate local rules and local connections. A typical cellular automata is defined on a grid. The grid at each point represents a cell and a finite state. The change rule is applicable to every cell and is carried out at the same time. The typical change rule depends on the state of cell and its (4 or 8) neighbor. Cellular automata has been used in physical simulation, biological simulation and other fields. Based on some interesting rules, this paper considers how to write an effective matlab program These cellular automata are implemented.)

操作系统实验，编程实现进程的调度，基于时间便轮转的算法！-Operating system, experiment, programming process, scheduling, time-based rotation algorithm will be!

mfoc程序基于nested authentication验证漏洞破解含有默认密码的M1卡的其他KEY。 mfcuk程序基于dackside原理破解全加密卡(The MFOC program is based on the nested authentication validation vulnerability to crack other KEY containing the default password M1 card. Mfcuk program cracking full encryption card based on dackside principle)

说明：  labview通过modbus读取omron ec55(labview access omron ec55 by modbus)