CFX默认空化模型CEL方法定义的CCL

区间覆盖问题的算法实现 问题描述：给出x轴上N条线段的坐标，从中选出一些线段来覆盖区间【0，M】，要求所用线段数目最少 -Interval coverage of the realization of the algorithm description: In this paper, x-axis N be the coordinates of line segment, selected to cover a number of line segments [interval 0, M], requirement by the number of segments at least

说明：  电网协调控制文献 下垂控制 多端柔性直流配电(Literature of Coordinated Control of Power Grid Droop Control Multi-terminal Flexible DC Distribution)

一本有效用于学习运算放大器的书籍，通过多种实验图纸给出了详细的工作状况(A book for effective learning of operational amplifiers)

说明：  autocad 截图利器，非常好用，白色底图，可以设置(AutoCAD screenshot sharp tool, very easy to use, white background, can be set)

魔方，相信很多人都玩过，这就是电脑上的魔方-Rubik

说明：  1. 硬件接线 （1）调试串口(UART_Debug)使用UART2，在“printf.h”文件中宏定义， 对应引脚为TX-PTD7，RX-PTD6 （在“uart.h文件中宏定义）。 （2）灯0~3（LIGHT_0~LIGHT_3）对应的引脚是PTC0~PTC3，高电平点亮（由硬件接法决定） （3）SPI0_CLK对应的引脚是PTE0， SPI0_MOSI对应的引脚是PTE1， SPI0_MISO对应的引脚是PTE2，SPI0_PCS对应的引脚是PTE3， SPI1_CLK对应的引脚是PTG4， SPI1_MOSI对应的引脚是PTG5， SPI1_MISO对应的引脚是PTG6，SPI1_PCS对应的引脚是PTG7。 （4）SPI0作为master,SPI1作为slave，SPI1接收SPI0发送的数据并产生中断。 用导线将PTE0与PTG4对接，将PTE1与PTG5对接，将PTE2与PTG6对接，将PTE3与PTG7对接。(1. Hardware wiring (1) Debugging Serial Port (UART_Debug) uses UART2, macro-defined in "printf.h" file, corresponding pins are TX-PTD7, RX-PTD6. (macro definition in the uart.h file). (2) The pins corresponding to the lamp 0~3 (LIGHT_0~LIGHT_3) are PTC0~PTC3, and the high-level lighting is determined by the hardware connection. (3) The pin corresponding to SPI0_CLK is PTE0, and the pin corresponding to SPI0_MOSI is PTE1. The pin corresponding to SPI0_MISO is PTE2, and the pin corresponding to SPI0_PCS is PTE3. The pin corresponding to SPI1_CLK is PTG4, and the pin corresponding to SPI1_MOSI is PTG5. The pin corresponding to SPI1_MISO is PTG6, and the pin corresponding to SPI1_PCS is PTG7. (4) SPI0 acts as master and SPI1 acts as slave. SPI1 receives data sent by SPI0 and generates interruption. PTE0 and PTG4 are docked by wire, PTE1 and PTG5 are docked, PTE2 and PTG6 are docked, PTE3 and PTG7 are docked.)

说明：  多项式拟合基线，多种方法，含有多个文件，还可以(Polynomial fitting baseline)

Earth fault simulation in 10 kV system with EMTDC PSCAD. Earth fault simulation in 10 kV system with EMTDC PSCAD. Earth fault simulation in 10 kV system with EMTDC PSCAD.

说明：  自己编写的用于STC12系列单片机 驱动 CH452键盘控制芯片的驱动程序(I have written STC12 Series single-chip driver for the keyboard controller chip CH452 driver)

虚拟打印机，可以预览你要打印的文件，图片等，非常的方便直观。-Virtual printer, you can preview the file you want to print, pictures, etc., very easy and intuitive.