-
chenxu
基于MATLAB的fft电力谐波分析 matlab代码(MATLAB' s fft-based harmonic analysis of power)
- 2009-04-23 10:15:59下载
- 积分:1
-
Npsopudn
partical swarm optimization method for optimize antenna array...
- 2013-08-14 19:30:14下载
- 积分:1
-
ond_mono_auto
The traditional power droop controllers are commonly used in distributed generation (DG) units to share the loads among the parallel inverters. However, the parameters of the power transmission and distribution line in microgrid are small and generally presented high resistance-to-inductance (R/X) ratio which will seriously influence the performance of the traditional power droop controller, even leading to instability
- 2013-11-17 05:34:31下载
- 积分:1
-
nengliangjiance
认知无线电主用户信号为BPSK信号在不同信噪比下的检测概率和虚警概率(Cognitive radio primary user signal is BPSK signals in different SNR detection probability and false alarm probability)
- 2013-11-15 17:28:34下载
- 积分:1
-
showcontextmenu_v2
使用方法如下:
---------------------------------
hcmenu1= uicontextmenu
uimenu(hcmenu1,...)
uimenu(hcmenu1,...)
showcontextmenu(hObj,hcmenu1)
---------------------------------
尝试使用实例test_showcontextmenu.m。
这也包含了日常琐碎的一些功能:
getParentFigure(hObject)
%的投资回报hObject的父母图
getPositionOnFigure(hObject,单位)
%返回对象的绝对位置上的数字
getRelPosition(hObject,单位)
%的人能(hObject, 定位 )与特定的 单位 (Use as follows:
---------------------------------
hcmenu1 = uicontextmenu
uimenu(hcmenu1,...)
uimenu(hcmenu1,...)
showcontextmenu(hObj,hcmenu1)
---------------------------------
Try test_showcontextmenu.m for usage example.
This also contains a number of trivial routine functions:
getParentFigure(hObject)
returns hObject s parent figure
getPositionOnFigure( hObject,units )
returns absolute position of object on a figure
getRelPosition( hObject,units )
get(hObject, Position ) with specific units )
- 2011-05-23 11:25:13下载
- 积分:1
-
123456
该程序完成了针对卫星姿态控制系统的执行器故障诊断和传感器故障诊断(The program has completed for the actuator fault diagnosis of satellite attitude control system and sensor fault diagnosis)
- 2013-05-09 17:53:17下载
- 积分:1
-
dwadw4
说明: 切削力随着磨削深度、速度的增大的趋势,这对于切削过程来说是非常重要的,如果增加相应的参数,就会导致不同的结果(The cutting force increases with the grinding depth and speed, which is very important for the cutting process. If the corresponding parameters are increased, the results will be different)
- 2020-07-13 14:39:53下载
- 积分:1
-
CS
CS仿真此仿真详细的列出了仿真的过程,并给予文字说明,是初学者的好资源!(CS simulation)
- 2013-04-28 14:30:47下载
- 积分:1
-
parta
Architecture Lab Part A,计算机系统导论实验作业(Architecture Lab Part A)
- 2013-12-26 15:11:42下载
- 积分:1
-
hart
HART协议文本,很难找到的,对开发HART协议相关特别有用。(HART text of the agreement, it is difficult to find, on the development of HART protocol related particularly useful.)
- 2020-11-25 15:29:32下载
- 积分:1