登录
首页 » Fortran » ModelC_alloy

ModelC_alloy

于 2020-06-24 发布
0 302
下载积分: 1 下载次数: 4

代码说明:

说明:  采用相场方法,计算合金中枝晶生长,标记为相场模型C_alloy。(Dendrite growth in the alloy was calculated by phase field method and marked as phase field model C_alloy.)

文件列表:

ModelC_alloy\input, 201 , 2010-11-11
ModelC_alloy\Int_position, 2450000 , 2010-11-11
ModelC_alloy\loader.f90, 110 , 2010-11-11
ModelC_alloy\Makefile, 1085 , 2010-11-11
ModelC_alloy\manager.f90, 241 , 2010-11-11
ModelC_alloy\modelC_alloy, 164456 , 2010-11-11
ModelC_alloy\README.txt, 1190 , 2010-11-11
ModelC_alloy\solver_mod.f90, 9020 , 2010-11-11
ModelC_alloy\surff.m, 1369 , 2010-11-11
ModelC_alloy\util_mod.f90, 4892 , 2010-11-11
ModelC_alloy\variables_mod.f90, 2171 , 2010-11-11
ModelC_alloy, 0 , 2019-07-08

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • servo
    PFC模型的围压伺服代码 可直接应用 为最新5.0版本代码(code of PFC the servo code to model version 5.0)
    2020-06-18 05:40:01下载
    积分:1
  • dms_rad
    说明:  实现角度向弧度的转换,并判断所属象限。。。(Realize the conversion of angle to radian, and judge the quadrant.)
    2019-01-13 19:15:49下载
    积分:1
  • radar
    1、目标速度引起的失真,时间膨胀因子10%、chirp中心频率偏移5%。 2、超高速运动对脉冲压缩的影响,多普勒频移补偿(Distortion caused by target speed, time dilation factor 10%, and chirp center frequency offset 5%. Effects of ultra high speed motion on pulse compression and Doppler frequency shift compensation)
    2017-06-03 12:06:47下载
    积分:1
  • 三极管放大电路设计
    说明:  三极管放大实验电路,包括固定偏置/分压偏置,需要根据一些参数确定所选用的电阻值,使得三极管工作在放大状态。本程序将电路设计设计成GUI模式,界面上只需要输入电路设计所需参数,根据相关理论推导,给出相关参数的理论值(放大倍数、输入电阻、输出电阻等),指导实验电路搭建。软件搭建在matlab gui上,方便使用 若干参数说明 beta:三极管放大倍数 Ic:集电极电流 Uce:期望CE间电压 UeCof:Re电阻上点电压与Ucc电压比值,一般0.1-0.2 IbCof:Ib上电流与流过Rb1、Rb2电流的比值,一般0.1 ShuntCe:是否有旁路电容(The experiment circuit of triode amplification, including fixed bias / partial voltage bias, needs to determine the selected resistance value according to some parameters to make the triode work in the amplification state. In this program, the circuit design is designed into GUI mode. Only the parameters needed for circuit design are needed on the interface. According to the relevant theoretical derivation, the theoretical values of the relevant parameters (magnification, input resistance, output resistance, etc.) are given to guide the construction of experimental circuit. The software is built on Matlab GUI, easy to use)
    2020-04-29 15:11:59下载
    积分:1
  • 源程序
    激光器中光场稳定分布过程的数值仿真,matlab编写,简单实用(laser light profile simulation)
    2019-08-06 18:12:00下载
    积分:1
  • 不同边界条件下均匀直梁固有频率计算软件源代码
    说明:  本软件用于计算不同边界条件下均匀直梁横向、纵向前三阶固有频率。(The software is used to calculate the first three natural frequencies of the transverse and longitudinal direction of a uniform straight beam under different boundary conditions.)
    2019-12-13 18:34:06下载
    积分:1
  • 计算文档
    根据W-M的分形函数,生成W-M函数的曲线,请批评指教。(Programme of W-M function)
    2021-03-23 16:29:15下载
    积分:1
  • MIMO_detection
    多天线系统的各种信号检测算法包括迫零,最小均方误差,最大似然,改进的最大似然等(A variety of multi-antenna systems signal detection algorithm, including zero-forcing, minimum mean square error, maximum likelihood, the improved maximum likelihood, etc.)
    2021-04-24 20:58:46下载
    积分:1
  • Cryo_L1b_read
    用于读取欧空局Cryosat-2卫星搭载的SARAL高度计获取的SARin L1b数据.(It is used to read SARin L1b data obtained from the SARAL altimeter carried by the ESA Cryosat-2 satellite.)
    2021-03-15 21:29:22下载
    积分:1
  • CPLGOO
    用JAVA实现的一个模拟tlenet的客户端 很实用的(Using JAVA implementation of a simulation tlenet client is very practical)
    2017-04-19 17:38:46下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载