相控阵雷达天线模型及仿真

为了优化协作通信系统的性能 ,提出了一种基于信道容量增益的中继节点选取策略 ,并在此基础上提出了源节点和中继节点最优功率分配算法. 协作通信 中继节点选取 功率分配 凸优化(A joint optimization st rategy for relay selection and power allocation is proposed to optimize the performance of cooperative communication system.cooperative communication relay selection power allocation convex optimization)

仿真图是速度、距离、幅度三维图像，插值与拟合的matlab实现，计算两个矩阵之间的欧氏距离。( FIG simulation speed, distance, amplitude three-dimensional image, Interpolation and fitting matlab implementation, Calculation of the Euclidean distance between the two matrices.)

关于天线原理的PPT。等同于教科书。很全。(PPT of antenna principle.Can be used as teaching book. A complete one.)

Modbus协议及Modbus RTU的C51编程(Modbus RTU Modbus protocol and the C51 programming)

说明：  ethernet mac vhdl verilog basic

SIM卡为表示能够执行proactive command且支持SAT，它必须在文件EFphaseTKG EFsst中有相关数据。 Phase文件指的是SIM卡所支持的GSM标准的级数，值为3则指SIM卡支持GSM phase 2和设置下传功能（profile download)。SST文件包含支持哪些GSM性能的准确信息。(SIM card that can support the implementation of proactive command and the SAT, it must file EFphaseTKG EFsst have relevant data. Phase document refers to the SIM card supports the GSM standard series, a value of 3 means the SIM card supports the GSM phase 2 and settings transfer function (profile download). SST file which contains support for GSM performance of accurate information.)

张贤达的盲信号处理讲义 包括盲源分离，斜投影。联合对角化。非负矩阵分解的介绍(blind source separation by Pro. Zhang xian da.)

Underwater optical wireless communication network

本文研究了SMBus 规范，介绍了典型的基于片上系统（SoC）设计的知识产权核（IP）实现，采用自顶向下 (Top-down)的集成电路设计方法完成了设计，并架构了基于总线功能模型(BFM)的验证平台 完成功能仿真，顺利完成了逻辑综合和时序仿真。FPGA 验证和投片后测试均表明设计具有 良好的性能。(This paper studies the SMBus specification, based on the introduction of the typical system-on-chip (SoC) intellectual property core design (IP) implementation, using top-down (Top-down) of the integrated circuit design methods achieve a design and architecture based on the total Line functional model (BFM) achieve functional verification platform for simulation, successfully completed a logic synthesis and timing simulation. FPGA silicon validation and post-tests show that the design has good performance.)

Multiple input multiple output techniques combined with orthogonal frequency division multiplexing (MIMO-OFDM) provide a promising approach for wireless systems. However, a serious drawback of the OFDM system is the high peak-toaverage power ratio (PAPR), which may severely affect the power efficiency of RF power amplifiers. In this paper, we propose a simple method to reduce the PAPR of MIMO-OFDM signals based on the use of unused subcarriers. Instead of processing the signals at each transmitter separately, a peak cancelling signal is generated at one antenna and is then applied to all the others with only simple modifications. Simulation has shown that a minimum 2 dB reduction in PAPR can be achieved for all transmit signals using this approach. As the signal processing is nearly all done at a single transmitter, repetition of the operations at each transmitter is avoided, and therefore the overall cost of the system can be significantly reduced.