MiniBalanceV5.0

一个数字类型可提高开关电源的设计与实现，可以是很好的借鉴，但是要用特殊软件打开，把文件后缀复制到百度就可以找到(A digital type can increase the switching power supply design and implementation, can be a good reference, but use special software to open, copy the file suffix can be found on Baidu)

Program IR for 5104

说明：  3KW数字llc电源源代码，学习参考。。(3KW Digital LLC Power Source Code)

USB CDC settings for STM32F407 - DESCOVERY with examples

说明：  基于VC++的51单片机实现LED灯闪烁源码(51 single-chip microcomputer based on VC ++ to realize the source code of LED flashing)

设计报告和设计方案，相信对参加飞思卡尔竞赛的有帮助。(The design report and design plan are believed to be helpful for participating in the Freescale Competition.)

AVR128显示部分，用12864作为显示的程序代码，已经调试通过(AVR128 display section, with 12864 as display the program code, have debugging through)

基于51单片机的译码器实验，常见问题： 1. 按下按键无效果 确保连线正确 换根杜邦线试试 将单片机拆下来重新安装下，重启开发板(Decoder Experiment Based on 51 Single Chip Microcomputer, Common Problems: 1. Pressing the key has no effect Make sure the connection is correct Try changing the dobang line Remove the microcontroller and reinstall it. Restart the development board.)

C8051F340,CP2200,实现的串口转以太网程序(C8051F340, CP2200, implementation procedures for serial to Ethernet)

滤波器广泛应用于数字信号处理、通信、自动控制领域,但设计可变宽频带有源滤波器则比较困难。利用单片机控制参数可编程的双二阶通用开关电容有源滤波器,精确设置有源滤波器的中心频率f，品质因数Q及有源滤波器的工作方式。本系统主要分为两个部分:即程控滤波器和程控放大器。程控放大器电压增益为40dB，通过单片机控制DA进行分压，可精确实现要求的10dB步进，误差小于0.5 ，通带为100Hz-500KHz，输入电压峰－峰值范围为10mV，在输入范围内无明显失真。由MAX264为核心的滤波器，可设置为高通、低通滤波器。通过单片机直接给出控制频率，使-3dB截止频率在1KHz-20KHz内可调，步进1KHz，误差小于1 。整个系统以52单片机为控制核心，电路简单，性能稳定，且具有较高精度，滤波参数调节通过单片机控制，较为方便。(Filters are widely used in digital signal processing, communications, automatic control area, but the design variable wideband active filter is more difficult. Control parameters using single-chip programmable universal switched-capacitor biquad active filter, active filter accurately set the center frequency f, quality factor Q and the active filter works. The system is mainly divided into two parts: the program-controlled filters and programmable amplifiers. Programmable amplifier voltage gain of 40dB, the DA through the partial pressure of single-chip control, can accurately achieve the required 10dB step, the error is less than 0.5 , passband to 100Hz-500KHz, input voltage peak- the range of 10mV, the input range no significant distortion. By the MAX264 as the core of filter can be set to high pass, low pass filter. Given directly by the microcontroller controls the frequency, the-3dB cutoff frequency at 1KHz-20KHz adjustable, step 1KHz, error is less than 1 . The entire system for)