RP-1311

说明：  Download this file when you experience d3dx9 error

该程序是完整的９８３４的测试程序，可以将这程序转变成Ｃ程序，直接可用-The program is a complete 9834 test procedures, these procedures can be transformed into C procedures directly available

说明：  用于提取时间序列的趋势项，去除趋势项的matlab代码，可以用于时间序列分析(The matlab code used to extract the trend term of time series and remove the trend term can be used for time series analysis)

说明：  利用AUTOLISP进行CAD二次开发，里面画了盘式法兰的两个视图，适合新手(Using AUTOLISP to redevelop CAD, two views of disc flange are drawn, which is suitable for beginners.)

说明：  588端全图飞行分享： 解压文件，用PCK将instance.txt文件替换客户端elementl文件夹下，configs.pk文件里config目录中的同名文件 gs.conf替换服务端中gamed/里的gs.conf(588 end full picture flight sharing: Extract the file, replace the instance.txt file with PCK in the client elementl folder, and replace the file with the same name in the config directory of configs.pk file Gs.conf replaces gs.conf in gamed / of the server)

用VC写的OPC客户端。直接可以使用。 有详细的说明。OPC服务器请选择WINCC 其他的也就不多说了非常好的代码-VC wrote OPC client. Direct can be used. A detailed explanation. OPC server, select WINCC other will not say more than a very good code

贝叶斯实现方法 很简单使用 希望大家继续完善-bayes

1. 硬件接线 （1）调试串口(UART_Debug)使用UART2，在“printf.h”文件中宏定义， 对应引脚为TX-PTD7，RX-PTD6 （在“uart.h文件中宏定义）。 （2）灯0~3（LIGHT_0~LIGHT_3）对应的引脚是PTC0~PTC3，高电平点亮（由硬件接法决定） （3）SPI0_CLK对应的引脚是PTE0， SPI0_MOSI对应的引脚是PTE1， SPI0_MISO对应的引脚是PTE2，SPI0_PCS对应的引脚是PTE3， SPI1_CLK对应的引脚是PTG4， SPI1_MOSI对应的引脚是PTG5， SPI1_MISO对应的引脚是PTG6，SPI1_PCS对应的引脚是PTG7。 （4）SPI0作为master,SPI1作为slave，SPI1接收SPI0发送的数据并产生中断。 用导线将PTE0与PTG4对接，将PTE1与PTG5对接，将PTE2与PTG6对接，将PTE3与PTG7对接。(1. Hardware wiring (1) Debugging Serial Port (UART_Debug) uses UART2, macro-defined in "printf.h" file, corresponding pins are TX-PTD7, RX-PTD6. (macro definition in the uart.h file). (2) The pins corresponding to the lamp 0~3 (LIGHT_0~LIGHT_3) are PTC0~PTC3, and the high-level lighting is determined by the hardware connection. (3) The pin corresponding to SPI0_CLK is PTE0, and the pin corresponding to SPI0_MOSI is PTE1. The pin corresponding to SPI0_MISO is PTE2, and the pin corresponding to SPI0_PCS is PTE3. The pin corresponding to SPI1_CLK is PTG4, and the pin corresponding to SPI1_MOSI is PTG5. The pin corresponding to SPI1_MISO is PTG6, and the pin corresponding to SPI1_PCS is PTG7. (4) SPI0 acts as master and SPI1 acts as slave. SPI1 receives data sent by SPI0 and generates interruption. PTE0 and PTG4 are docked by wire, PTE1 and PTG5 are docked, PTE2 and PTG6 are docked, PTE3 and PTG7 are docked.)

根据颜色初步提取目标，二值化处理，边缘检测，霍夫变换提取目标(According to the color initial extraction, two value processing, edge detection and Hof transform are used to extract the target.)

自己写的扫雷，不需要图片加载，纯手绘图片-Write their own de-mining, no image loaded, pure hand-painted picture