1

multi tier protocol for wireless sensor networks

说明：  这是一个包括程序和文档在内的高斯低通滤波器的设计与实现过程，对于滤波器初学者很有用。(This is a prediction program that can realize Arima. The program is labeled and easy to understand.)

在dos下使用汇编接口，中断等知识做的俄罗斯方块 ，是学习汇编和微机原理的好东西-dos used in the compilation interface, interrupted knowledge of the Russian box do, is a compilation and computer learning theory a good thing

1. 硬件接线 （1）调试串口(UART_Debug)使用UART2，在“printf.h”文件中宏定义， 对应引脚为TX-PTD7，RX-PTD6 （在“uart.h文件中宏定义）。 （2）灯0~3（LIGHT_0~LIGHT_3）对应的引脚是PTC0~PTC3，高电平点亮（由硬件接法决定） （3）SPI0_CLK对应的引脚是PTE0， SPI0_MOSI对应的引脚是PTE1， SPI0_MISO对应的引脚是PTE2，SPI0_PCS对应的引脚是PTE3， SPI1_CLK对应的引脚是PTG4， SPI1_MOSI对应的引脚是PTG5， SPI1_MISO对应的引脚是PTG6，SPI1_PCS对应的引脚是PTG7。 （4）SPI0作为master,SPI1作为slave，SPI1接收SPI0发送的数据并产生中断。 用导线将PTE0与PTG4对接，将PTE1与PTG5对接，将PTE2与PTG6对接，将PTE3与PTG7对接。(1. Hardware wiring (1) Debugging Serial Port (UART_Debug) uses UART2, macro-defined in "printf.h" file, corresponding pins are TX-PTD7, RX-PTD6. (macro definition in the uart.h file). (2) The pins corresponding to the lamp 0~3 (LIGHT_0~LIGHT_3) are PTC0~PTC3, and the high-level lighting is determined by the hardware connection. (3) The pin corresponding to SPI0_CLK is PTE0, and the pin corresponding to SPI0_MOSI is PTE1. The pin corresponding to SPI0_MISO is PTE2, and the pin corresponding to SPI0_PCS is PTE3. The pin corresponding to SPI1_CLK is PTG4, and the pin corresponding to SPI1_MOSI is PTG5. The pin corresponding to SPI1_MISO is PTG6, and the pin corresponding to SPI1_PCS is PTG7. (4) SPI0 acts as master and SPI1 acts as slave. SPI1 receives data sent by SPI0 and generates interruption. PTE0 and PTG4 are docked by wire, PTE1 and PTG5 are docked, PTE2 and PTG6 are docked, PTE3 and PTG7 are docked.)

说明：  Wind Energy in Algeria: A Brief Overview

经典的机组组合程序，使用yalmip解决电力系统机组组合程序(Classical unit commitment program, using yalmip to solve unit commitment program in power system)

说明：  超声波测距并且oled显示，误差小，精度高，基于51单片机(Ultrasonic ranging and OLED display, small error, high precision, based on 51 single chip microcomputer)

CAA开发者可以参考本资料进行CAA二次开发。(CAA developers can refer to this data for the two development of CAA.)

迷宫问题的算法,用c实现的-maze of algorithm, with the realization c

通配符匹配程序，详细见注释-wildcard matching procedures, detailed see Notes