多普勒频移条件下的 8-PSK调制解调及同步算法仿真

为了提高MIMO-OFDM系统的数据传输率和频谱利用率,提出一种新的自适应算法。该算法在保证信道质量所需误码率和总发射功率的前提下,按照各个子载波衰落程度动态地分配比特和功率,使系统的总数据传输速率最大。理论分析得出,该算法降低了系统运算复杂度,能很大地改善系统的整体性能。(In order to improve data transmission rates and spectrum efficiency of MIMO-OFDM systems,this paper proposes a new adaptive algorithm. While the channel transmission quality to meet the requirements of a certain target BER(bit error rate) and total emissive power,according to each sub-carrier decline degree to adjust each sub-carrier modulation method freely,try to minimize the total data rate of system. Theory analysis shows the algorithm can reduce system complexity and improve overall performance of the ...)

给出了OFDM在卫星通信中的系统框图并 在Simulink中仿真实现，利用改进的CMA恒模算法进行盲均衡处理，来去除时变卫星信道对信号的影响,基于4阶累积量的方法 将OFDM信号与其他调制类型信号区分开来(OFDM is given in the satellite communication system block diagram and Simulation in Simulink using the modified constant modulus algorithm CMA for blind equalization, to remove the time-varying satellite channel on the signals, based on 4-order cumulant method OFDM signals and other types of signal modulation to distinguish)

说明：  大规模MIMO中采用天线选择来降低系统复杂度和成本，其中包括最优天线选择和递减天线选择，快速天线选择和基于范数的天线选择算法。(Antenna selection is used in large-scale MIMO to reduce system complexity and cost, including optimal antenna selection and decreasing antenna selection, fast antenna selection and antenna selection algorithm based on norm.)

OPNET上实现的原码，与卫星通信有关，有兴趣的可以下载(OPNET to achieve the original code, relating to satellite communications, are interested in can be downloaded)

利用MATLAB/Simulink建立直线电机模型(Using MATLAB/Simulink to establish a linear motor model)

模拟空间多孔介质,用matlab三维曲面重构。(The porous media in the space is simulated, and the three-dimensional surface is reconstructed.)

Smoothing Filter-based Intensity Modulation a spectral preserve

说明：  汽车行业CAN通讯SAEJ1939标准英文版(Auto Industry CAN Communication SAEJ1939 Standard English Edition)

说明：  G P S和G S M 双定位终端的软硬件设计与实现 :随着移动定位技术的发展， 单纯的签子G P S 的定位终端或者荃于移动网络的定位终端都将无法浦足用户的俩求。前者的G P S定 位信号受地形及建筑物的影晌，会存在定位盲区 后者定位精度和定位能力受到移动网 络的限制。该文提出一种集成了G P S定位和G S M 网络定位技术的定位终端，阐述了它的软硬件的设计和实现。实验结果表明，该定位终端结合了G P S和G S M网络两种定位方式的优点，(D e s i g n a n d I m p l e me n t a t i o n o f t h e T r a c k i n g T e r mi n a l I n t e g r a t i n g GP S wi t h GS M P o s i t i o n i n g T e c h n o l o g y J I A NG X i r u i , C HE N G Z h e n l i n , F AN G J i n y u n , Z HA NG L i v n g ( I n s t i t u t e o f C o m p u t e T e c h n o l o g y , C h i n e s e A c a d e m y o f S c i e n c e s , B e i j i n g 1 0 0 0 8 0 ) b s t r a c t ] Th e t r a c k i n g t e r mi n a l p l a y s a n i mp o r a n t rl e i n t h e n a v i g a t i o n a n d p o s i t i o n i n g s y s t e m. Ho w t o t h e t r a c k i n g t e r mi n a l i s a k e y p rb l e m t o t h e d e s i g n e r a n d u s e r . T h i s p a p e r p r e s e n t s a me t h o d wh i c h i mpr v e t i n t e g r a t e s p e r f o r m a n c e a n d p r e c i s i o GP S wi 比GS M p o s i t i o n i n g h n o l o g y i n o n e t e r mi n a l , a n d s p e c i f i e s t h e s o f)

本人用石川法求齿轮的啮合刚度，完整版的程序，里面可以运行啮合刚度图(Meshing Stiffness of Gears Calculated by Ishikawa Method)