VectorCanSubVI

通过labview实现tcp协议的通信，可以使用虚拟串口和电脑通信(The communication of TCP protocol can be realized by labview. Virtual serial port and computer communication can be used.)

labviewUSB测试上位机程序，用于测试上位机与usb设备之间的通讯。(labview USB master,LabVIEW USB test host computer program, used to test the communication between host computer and USB device.)

1．采用Labview设计一虚拟函数信号发生器， 通过数据采集卡输出波形信号，调节信号的相关参数，可观察示波器上波形的变化情况。 ⑴ 以NI MyDAQ数据采集卡作为输出接口； ⑵ 数据采集卡输出多种信号，至少完成三种波形：正弦波、三角波、方波(可调占空比)的输出，同时前面板上显示各输出波形； ⑶ 频率、幅值、初相位、直流偏移量和方波的占空比（0～100 ）等参数可以通过前面板控件调节。 ⑷ 前面板可显示输出波形。(1. Labview design using a virtual function signal generator, data acquisition card output waveform signal, adjust the relevant parameters of the signal can be observed on an oscilloscope waveform changes. ⑴ with NI MyDAQ data acquisition card as output interface ⑵ data acquisition card output a variety of signals, to complete at least three waveforms: sine wave output, triangle wave, square wave (adjustable duty cycle), while each of the output waveform is displayed on the front panel ⑶ frequency, amplitude, initial phase, the DC offset and duty cycle square wave (0 to 100 ) and other parameters via the front panel controls to adjust. ⑷ output waveform can be displayed on the front panel.)

说明：  这个包中包含各种子vi，可以完成对线阵CCDTD1304的数据采集功能(Can complete the data reading function of the line CCD)

说明：  用于labview数据库编程，相关指导资料(Used for LabVIEW database programming, related guidance materials)

在LabVIEW环境下实现全景照相。在手动转动摄像头前提下，程序实现图像拼接，照片保存。(BASED on LabVIEW the program can achieve the function which panoramic camera can do,besides, it can also let you save your photos in your hardwire while your camer is connect with the computer)

3σ准则 利用LabVIEW编写 剔除粗大误差(to Elimitate the gross error)

说明：  输控制协议（TCP，Transmission Control Protocol）是一种面向连接的、可靠的、基于字节流的传输层通信协议，由IETF的RFC 793定义。TCP旨在适应支持多网络应用的分层协议层次结构。(Transmission Control Protocol (TCP) is a connection-oriented, reliable, byte-stream-based transport layer communication protocol defined by IETF RFC 793. TCP aims at adapting to the hierarchical protocol structure supporting multi-network applications.)

是LABVIEW的课设，有需要的可以参考一下 虚拟信号采集分析器 1）：利用虚拟信号发生器产生不同信号（信号的相关参数可调） 2）：在信号上叠加白噪声。 3）：对上述信号进行采样（采样频率可调） (LabVIEW course design, need to reference a virtual signal collecting analyzer 1): using virtual signal generator to generate different signal (signal parameters can be adjusted) 2): signal in additive white noise. 3): the above signal sampling (sampling frequency can be adjusted))

说明：  自己做了一个用labview对CRC32数据进行计算处理的Vi(I made a VI to calculate and process CRC32 data with LabVIEW)