paper4

opnet与matlab联调的步骤，过程详细，使用方便(Steps of OPNET and MATLAB debugging, detailed process, easy to use)

详细介绍了西门子PLC的间接寻址方法，对于应用西门子PLC很有用处。(Detailed the the Siemens PLC indirect addressing method is useful for the application of the Siemens PLC.)

说明：  在实际的调谐解调电路中，采用的是非相干载波解调，本振信号与发射端的载波信号存在频率偏差和相位抖动，因而解调出来的模拟I、Q基带信号是带有载波误差的信号。这样的模拟基带信号即使采用定时准确的时钟进行取样判决，得到的数字信号也不是原来发射端的调制信号，误差的积累将导致抽样判决后的误码率增大，因此数字QPSK解调电路要对载波误差进行补偿，减少非相干载波解调带来的影响。(In the actual tuning and demodulating circuit, non-coherent carrier demodulation is adopted, and the frequency deviation and phase jitter of the local oscillator signal and the carrier signal of the transmitting end are present, and thus the demodulated analog I and Q baseband signals are signals with carrier error.)

不错的客户端连接程序，希望大家喜欢，里面是一个客户端的程序，一会会提供服务端的程序(good client procedures in the hope that everyone likes, there is a client process, will provide a service side of the process)

GSM reading book in the would

说明：  基于马尔科夫的图像分割代码，可运行，可运行，可运行(Image segmentation code based on Markov, can run, can run, can run)

说明：  STC单片机多机连级串口程序可实现.416路控制. 串口和485都可以使用、 一个程序可以用在26块控制板上，通过拔码开关给板子编号，每块板可以过滤分析所接收到不同的代码。进行继电器的动作，能返回数据，因使用定时器发送返回，不会阻塞或者代码错乱、可以 用在中控，物联网，等各种控制场合。修改代码后，能达到上千路的控制。(STC single-chip microcomputer multi-level serial port program can realize 416 channel control. Serial port and 485 can be used. One program can be used on 26 control boards. Each board can filter and analyze different codes received by numbering the boards with the pull-out switch. Relay operation can return data, because the timer is used to send the return, it will not block or code confusion, and can be used in central control, Internet of things, and other control occasions. After modifying the code, it can achieve thousands of control.)

极化码编译码在matlab下的仿真 误码性能分析(Analysis of Error Performance of Polarization Coding and Decoding under Matlab)

本程序是对V-BLAST系统及其检测算法的仿真，可采用BPSK,QPSK,16QAM,64QAM调制。检测算法为ML，MMSE,ZF,以及采用迫零的连续干扰消除检测算法。(This procedure is a V-BLAST system and its detection algorithm of the simulation, using BPSK, QPSK, 16QAM, 64QAM modulation. Detection algorithm for the ML, MMSE, ZF, and the introduction of zero-forcing successive interference cancellation detection algorithm.)

本文系统的介绍了TQ2440开发板相关知识，对这方面的读者很有作用。(This article describes the system development board TQ2440 knowledge, useful in this respect the role of the reader.)