登录
首页 » PDF » 基于随机森林的局放特征优选新方法

基于随机森林的局放特征优选新方法

于 2020-06-19 发布 文件大小:398KB
0 262
下载积分: 1 下载次数: 1

代码说明:

  提出了一种基于随机森林的局放特征优选新方法。结果证明,随机森林算法是一种有效的电缆局放特征优选方法,并有望推广到其他电力设备局放的特征寻优。(A new method based on Stochastic Forest for local feature selection is proposed. The results show that the stochastic forest algorithm is an effective method for feature optimization of Cable Partial discharge, and it is expected to be extended to other power equipment partial discharge feature optimization.)

文件列表:

基于随机森林的高压电缆局部放电特征寻优_王干军.pdf, 651888 , 2019-08-05

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 新建 WinRAR ZIP 压缩文件
    DMA transmission with STM32 f10x, including the driver file about STM32 f10x
    2020-06-22 15:00:01下载
    积分:1
  • MPM3D-F90-master
    说明:  张雄mpm的开源软件,很简单实用,现在已经出了非开源版本。(Zhangxiong MPM open source software, very simple and practical, has now been out of the non-open source version.)
    2020-06-18 11:00:01下载
    积分:1
  • character_changed_to_number
    一个用Labview编写的字符串转数字的程序(this program which develop by Labview is used to change character to number)
    2009-09-05 09:34:36下载
    积分:1
  • VB
    EPSON VB6.0 OPOS开发源代码,很好用的(EPSON VB6.0 OPOS development source code, very good use)
    2013-09-17 14:50:12下载
    积分:1
  • 一个java开发的俄罗斯方块游戏,希望大家喜欢!
    一个java开发的俄罗斯方块游戏,希望大家喜欢!-a java development of the game Tetris, hope you like them!
    2022-07-10 22:47:30下载
    积分:1
  • PC与汇川PLC_ModbusTCP_Test
    说明:  上位机读写汇川H3U PLC的寄存器与继电器(Register and Relay of H3U PLC for Upper Computer Reading and Writing)
    2021-04-23 20:58:47下载
    积分:1
  • CH11-KEA128-SPI
    说明:  1. 硬件接线 (1)调试串口(UART_Debug)使用UART2,在“printf.h”文件中宏定义, 对应引脚为TX-PTD7,RX-PTD6 (在“uart.h文件中宏定义)。 (2)灯0~3(LIGHT_0~LIGHT_3)对应的引脚是PTC0~PTC3,高电平点亮(由硬件接法决定) (3)SPI0_CLK对应的引脚是PTE0, SPI0_MOSI对应的引脚是PTE1, SPI0_MISO对应的引脚是PTE2,SPI0_PCS对应的引脚是PTE3, SPI1_CLK对应的引脚是PTG4, SPI1_MOSI对应的引脚是PTG5, SPI1_MISO对应的引脚是PTG6,SPI1_PCS对应的引脚是PTG7。 (4)SPI0作为master,SPI1作为slave,SPI1接收SPI0发送的数据并产生中断。 用导线将PTE0与PTG4对接,将PTE1与PTG5对接,将PTE2与PTG6对接,将PTE3与PTG7对接。(1. Hardware wiring (1) Debugging Serial Port (UART_Debug) uses UART2, macro-defined in "printf.h" file, corresponding pins are TX-PTD7, RX-PTD6. (macro definition in the uart.h file). (2) The pins corresponding to the lamp 0~3 (LIGHT_0~LIGHT_3) are PTC0~PTC3, and the high-level lighting is determined by the hardware connection. (3) The pin corresponding to SPI0_CLK is PTE0, and the pin corresponding to SPI0_MOSI is PTE1. The pin corresponding to SPI0_MISO is PTE2, and the pin corresponding to SPI0_PCS is PTE3. The pin corresponding to SPI1_CLK is PTG4, and the pin corresponding to SPI1_MOSI is PTG5. The pin corresponding to SPI1_MISO is PTG6, and the pin corresponding to SPI1_PCS is PTG7. (4) SPI0 acts as master and SPI1 acts as slave. SPI1 receives data sent by SPI0 and generates interruption. PTE0 and PTG4 are docked by wire, PTE1 and PTG5 are docked, PTE2 and PTG6 are docked, PTE3 and PTG7 are docked.)
    2020-06-16 12:00:01下载
    积分:1
  • 3信号归一化频率实验
    说明:  基于Labview关于信号与系统的实验,主要是信号归一化频率实验(The experiment of correlation signal and system based on LabVIEW, mainly signal normalization frequency experiment)
    2020-02-14 17:39:44下载
    积分:1
  • niutoubaochuang
    牛头刨床仿真MATLAB相关程序,可以用来加载运动规律(Simulation of bullhead planer)
    2017-12-02 21:23:56下载
    积分:1
  • 在TI DSP单片机液晶显示测试程序
    lcd display test program in ti dsp mcu -lcd display test program in ti dsp mcu
    2022-03-22 08:57:24下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载