QT

说明：  使用数组的方法，通过向用户索要数据计算出学生的平均成绩。(Using the method of array, the average scores of students are calculated by asking for data from users.)

用于解决9*9的数独，功能不完善,只能给出所有结果中的一种。(to solve Sudoku 9* 9 , function is not perfect.)

说明：  在线聊天室工具，有客户端，服务端 原代码(Online chatroom tools, the client side, the server side of the original code)

说明：  310V-foc无感无刷直流电机之电调设计源代码。(The source code of the electric regulation design of the sensorless BLDCM)

计算器，可进行四则运算，并且有符号位，退格，以及小数点。(Calculator, can be carried out in four operations, and the sign bit, backspace, and decimal point.)

REGISTRAR is fully documented msdn.Il can do this without too many complications and requires only a couple of IID, some definitions to be used.

利用SDN分布式实现了网络流量负载均衡的功能(The function of load balancing of network traffic is realized by using SDN)

说明：  canape工程，模拟发送报文配置，主要功能详见功能说明(canapeprogect.Analog send message configuration.)

实验器材: 探索者STM32F4开发板 实验目的: 学习DS18B20数字温度传感器的使用. 硬件资源: 1,DS0(连接在PF9) 2,串口1(波特率:115200,PA9/PA10连接在板载USB转串口芯片CH340上面) 3,ALIENTEK 2.8/3.5/4.3/7寸TFTLCD模块(通过FSMC驱动,FSMC_NE4接LCD片选/A6接RS) 4,DS18B20传感器一个(接在PG9上). 实验现象: 本实验开机的时候先检测是否有DS18B20存在，如果没有，则提示错误。只有在检测到DS18B20之后才开始 读取温度并显示在LCD上，如果发现了DS18B20，则程序每隔100ms左右读取一次数据，并把温度显示在LCD 上。同样我们也是用DS0来指示程序正在运行。(Experimental equipment: Explorer STM32F4 development board Objective: Learn the use of DS18B20 digital temperature sensor. Hardware resources: 1, DS0 (connected to PF9) 2, serial port 1 (baud rate: 115200, PA9/PA10 connection on board USB to serial port chip CH340). 3 inch TFTLCD ALIENTEK, 2.8/3.5/4.3/7 module (via FSMC driver, FSMC_NE4 LCD chip select /A6 RS) 4, one of the DS18B20 sensors (attached to PG9). Experimental phenomena: This experiment first detects whether there is DS18B20 when starting up. If not, it prompts errors. Only after the detection of DS18B20 did it begin Read the temperature and display it on LCD. If DS18B20 is found, the program reads data once every 100ms or so and displays the temperature at LCD. On. Similarly, we also use DS0 to indicate that the program is running.)

说明：  STC89S52单片机设计一款智能充电器的控制系统，通过对电压传感器和电流传感器的检测，当检测充电电压和电流大设置值时，自动断开充电电路。本设计由软件和硬件两部分组成，硬件设计对单片机最小系统、电压电流采集电路、充电控制电路、按键电路、液晶显示电路、报警电路等进行设计，使控制器具备电压、电流检测，系统参数显示，自动断电控制等功能；软件设计方面对控制器的软件驱动程序进行设计。并利用Protues软件进行可行性仿真，对软件和硬件设计进行验证(425/5000 STC89S52 mcu design a smart charger control system, through the voltage sensor and current sensor detection, when the detection charging voltage and current settings, automatically open the charging circuit. This design is composed of two parts: software and hardware. The hardware design designs the minimum system, voltage and current collection circuit, charging control circuit, key-press circuit, liquid crystal display circuit, alarm circuit, etc. , the controller has the functions of voltage and current detection, system parameter display, automatic power-off control and so on. The feasibility simulation is carried out by using Protues software to verify the design of software and hardware)