-
DTMF
模拟双音多频(DTMF)拨号系统的MATLAB仿真,形象画出了每个数字键所代表产生的波形(Simulation of Dual Tone Multi-Frequency (DTMF) dial-up system MATLAB simulation, the image drawn by the representative of the number keys for each generated waveform)
- 2020-11-23 20:49:33下载
- 积分:1
-
各工况测试曲线参数
说明: 车辆循环各种工况包括UDDS等,可用于车辆各种仿真(Various working conditions of vehicle cycle)
- 2021-02-19 10:45:38下载
- 积分:1
-
61850-new(新版本)
思科为IEC61850行业标准实现的源码库,其中提供MMS、GOOSE/SV完整的服务和例程。(Sisco provides a source library for IEC61850 industry standard implementation, which provides complete services and routines for MMS, GOOSE/SV.)
- 2021-03-11 10:19:26下载
- 积分:1
-
gridside
本模型采用矢量控制与SVPWM相结合的方法,应用在低压微电网中。直流源电压为600V,逆变器输出电压为380V,可实现稳定功率输出。模型对网侧控制策略中每一模块尽量做出了说明,方便初学者更快理解三相逆变器控制策略的实现方法,运行效果非常好。(This model adopts the method of combining vector control with SVPWM, which is applied in low voltage microgrid. The DC source voltage is 600V, and the inverter output voltage is 380V, which can achieve stable power output. Each module is explained as far as possible in the network side control strategy. It is convenient for beginners to understand the realization method of the three-phase inverter control strategy faster, and the operation effect is very good.)
- 2018-05-15 16:21:09下载
- 积分:1
-
rad_dms
说明: 实现弧度向角度的转换,判断在第几象限。。。。。。(Realize the conversion of radian to angle and judge the quadrant)
- 2019-01-13 19:12:24下载
- 积分:1
-
nec_bldc_ver1_IDC_FD_whole_07911
说明: 启航电动自行车控制器软件,已经量产。用于替换晶汇控制器。(BLDC controller for elec-bike)
- 2019-01-19 21:16:31下载
- 积分:1
-
lfmsk_code
这是matlab的代码,用于lfmsk雷达波形和比相法测角的仿真代码,望有用的人自取(this is used to simulate the lfmsk and angle figuring)
- 2021-04-20 19:28:50下载
- 积分:1
-
ModelC_pure
说明: 采用相场方法,计算纯物质枝晶生长,标记为相场模型C。(Dendrite growth of pure substance was calculated by phase field method, marked as phase field model C.)
- 2020-06-24 02:20:02下载
- 积分:1
-
radidn
关于ISAR运动补偿和SAR成像的matlab 源程序 不错的(About the ISAR motion compensation and matlab source good SAR imaging)
- 2017-05-11 23:29:11下载
- 积分:1
-
Arx1
说明: 选取四个点,自动判断是否在一个平面上。同一个平面上。则绘制一个多边形。不在一个平面,则以前三个点为底面,构成一个椎体。支持Move等转换命令,存图与开图,实现Jig交互绘制等。(Four points are selected to automatically determine whether or not they are on a plane. On the same plane. Draw a polygon. If it is not in a plane, the first three points are at the bottom, forming a vertebral body. Support Move and other conversion commands, save and open maps, Jig interactive rendering, etc.)
- 2020-06-16 08:40:02下载
- 积分:1