TI-RFID-antna

Build a Graphical User Interface to show off * uicontrols.

基于MATLAB软件的有关雷达杂波的的很多个程序，相信对初学入门者很有帮助 (Based on MATLAB software on the radar clutter of many programs, I believe that is helpful for beginners beginners)

bluetuch 检测程序,bluetuch 检测程序(bluetuch test source code .bluetuch test source code )

说明：  按FPE定阶的 源程序：fpe.cpp M序列：M序列.txt 白噪声：Gauss.txt 程序中先用依模型阶次递推算法估计模型的参数，再用fpe方法判断模型的阶次。 程序运行结果如下： n: 1 判断阶次FPE的值: 0.0096406 -0.481665 1.07868 n: 2 判断阶次FPE的值: 0.00875755 -0.446739 0.00498181 1.07791 0.0527289 n: 3 判断阶次FPE的值: 0.0087098 -0.459433 0.120972 -0.0569228 1.07814 0.0390757 0.116982 n: 4 判断阶次FPE的值: 0.000396884 -0.509677 0.4501 -0.200906 0.0656188 1.07991 -0.0156362 0.442989 0.0497236 n: 5 判断阶次FPE的值: 3.2095e-007 -1.18415 0.813123 -0.517862 0.34881 -0.116864 1.07999 -0.744141 0.474462 -0.253112 0.122771 n: 6 判断阶次FPE的值: 3.23349e-007 -1.14659 0.76933 -0.487651 0.329676 -0.10377 -0.00440907 1.07999 -0.703574 0.447253 -0.235282 0.113587 0.00479688 从以上结果可以看出，当n=5时，fpe值最小，所以这时的模型阶次和参数估计值为最优结果： 3.2095e-007 -1.18415 0.813123 -0.517862 0.34881 -0.116864 1.07999 -0.744141 0.474462 -0.253112 0.122771(err)

HFSS/UTD混合法计算电大尺寸导体上的天线(HFSS/UTD hybrid method to calculate the antenna on a large conductor)

计算损伤结构前后的响应，对已结构的分析具有很好的效果(After calculating the response of the structure damage, the structure analysis of a good effect)

滤波器设计是信号处理的核心问题之一,Matlab软件在多个研究领域都有着广泛的应用。 本文介绍了基于Matlab环境下,用窗函数设计法实现FIR数字滤波器的设计,并阐述了与以前人 们常用的设计方法的区别,给出了设计实例。仿真结果表明,设计结果的各项性能指标均达到指定 要求,且设计过程简便易行。 (The design of filters is a core problem in signal processing. MATLAB software iswidely used inmany research fields. This article introduces themethod ofusingwindow function to design FIR digital filters based onMATLAB and its differences from the tradi- tional designmethods. And itgives a design example. The simulation shows that the design results canmeet the requirements verywell and the design procedure is very simple and practica.l )

24G高集成度微波雷达芯片,一发二收，可组成阵列天线，数据处理后精度可达mm级(24 GHz transceiver MMIC with one transmitter and two receiver units • Fully integrated low phase noise VCO • Switchable prescaler with 1.5 GHz and 23 kHz output • On chip power and temperature sensors • Gilbert based homodyne quadrature receiver • Single ended RF input terminals)

电机转子台，断条缩孔的计算等，MATLAB等(Rotor sets, Breaking Shrinkage calculation, MATLAB, etc.)

虚拟工厂模式典型实例，通俗易懂，易学易仿(abstract factory example)