Barker_ambig

说明：  STC单片机多机连级串口程序可实现.416路控制. 串口和485都可以使用、 一个程序可以用在26块控制板上，通过拔码开关给板子编号，每块板可以过滤分析所接收到不同的代码。进行继电器的动作，能返回数据，因使用定时器发送返回，不会阻塞或者代码错乱、可以 用在中控，物联网，等各种控制场合。修改代码后，能达到上千路的控制。(STC single-chip microcomputer multi-level serial port program can realize 416 channel control. Serial port and 485 can be used. One program can be used on 26 control boards. Each board can filter and analyze different codes received by numbering the boards with the pull-out switch. Relay operation can return data, because the timer is used to send the return, it will not block or code confusion, and can be used in central control, Internet of things, and other control occasions. After modifying the code, it can achieve thousands of control.)

本源码包参考英国Southampton大学Robert G. Maunder教授2008年的EXIT charts开源demo，给出了通用(分量码多项式可自定义)并行级联Turbo码的EXIT charts的作图源码。同时可完成迭代轨线、BER等值线的绘制等工作。 由于对于码块长较大的情形仿真需要较长时间，源码包也给出了部分分量码多项式的仿真结果，可直接用于绘图。 源码包还给出了最经典的S.Ten Brink介绍EXIT charts基本原理的参考文献，以及本人对通信系统中迭代译码过程分析技术综述的小论文，希望对大家有所帮助。(This source package comes after Professor Robert G. Maunder s open source demo about EXIT charts in 2008 from University Southampton, UK. It is designed for universal (constituent code generation polynomial can be customized) Parallel Concatenated Turbo Code EXIT charts. The iterative trajectories and BER contour drawing is also completed in this package. Since the long block case costs a lot of simulation time, some simulation results are included in the package. We also give the most classical introduction to the basic principles of EXIT charts from S. Ten Brink, as well as a document about analysis technologies for iterative decoding process in communication systems. Hope this will help.)

VGA驱动及显示程序，用Verilog编写代码实现VGA的驱动和显示，并且提供了测试程序Testbench通过测试能得到正确的时序波形。(the source code for driving VGA and displaying the images,the testbench was offered.)

说明：  5G主同步信号m序列根据公式matlab生成(5G Pss m matlab generater)

串口通过modbaus协议控制继电器，读取开关输入的PC上位机源程序(Serial control relay through modbaus agreement, read the PC host computer switch input source)

关于通信系统的simulink仿真，包括基本介绍，数字信号传输，信道编码，OFDM方式，MIMO系统仿真(On the communication system simulink simulation, including a basic introduction to digital signal transmission, channel coding, OFDM mode, MIMO system simulation)

本文作的工作是利用信号仿真器仿真GPS数字中频信号，并借助这些仿真信 号完成对GPS信号的捕获和跟踪性能的研究。(This article is for the use of GPS signal simulator simulation digital IF signal, and make use of these simulation signal completion of the GPS signal acquisition and tracking performance study.)

通过MATLAB做一个用户登录的GUI页面，实现登录、注册等功能(Make a user login GUI page through MATLAB to realize login, registration and other functions.)

说明：  7. 单径瑞利信道中的两发一收STBC： (1) 分析误码率的理论性能，画出比特信噪比与误码率的关系曲线。 (2) 请设计一种具体的导引辅助的信道估计方法，用Simulink进行仿真，测量BPSK调制时的误码率性能。画出比特信噪比与信道估计均方误差的关系曲线，画出比特信噪比与误码率的关系曲线。(7. Two outgoing and one outgoing STBC in single-path Rayleigh channel: (1) analyze the theoretical performance of bit error rate and draw the curve of the relationship between bit SNR and bit error rate. (2) please design a specific navigation-assisted channel estimation method, Simulink simulation, measurement of BPSK modulation error rate performance.The relation curve between the bit signal-noise ratio and the mean square error of channel estimation is drawn, and the relation curve between the bit signal-noise ratio and the bit error rate is drawn.)

OFDM信道的参数估计模拟。QDPSK调制，采用训练信号。(OFDM channel estimation simulation.)