h5gSSS

这个程序除了接收机同步、信道编码没有加入外，基本上反映了一个OFDM系统的特性： 1. qpsk/16qam/64qam映射、解映射 2. OFDM调制解调（循环前缀，FFT等） 3. 非整数采样时刻多径时延的多径信道 4. Rayleigh或者Rician多径信道 5. 信道的连续时变（非block fading） 6. 线性插值信道估计 7. FFT变换域插值信道估计(In addition to this program receiver synchronization, channel coding have not joined, the basically reflect the characteristics of an OFDM system: 1. Qpsk/16qam/64qam mapping, mapping solution 2. OFDM modulation and demodulation (cyclic prefix, FFT, etc.) 3. Non- integer sampling instant multi-path delay of multi-path channel 4. Rayleigh or Rician multipath channel 5. a continuous time-varying channel (non-block fading) 6. linear interpolation channel estimation 7. FFT transform domain interpolation channel estimation)

TDMA simulation using OPNET modeler

Gardner位同步算法与锁相环的联合仿真程序.加入了时偏和频偏，能很好地锁定时偏和频偏，得到最佳采样输出。(Gardner bit synchronization algorithm and phase-locked loop joint simulation program, adding time offset and frequency offset, can well lock the bias and frequency offset, get the best sampling output.)

Dopod 838官方拆机及维修手册,很详细的说明，照着他一步一步拆，很简单的，我的手机坏了就是照他拆了修的。(Dopod 838 official TBM Break-down and maintenance manual, a very detailed explanation, he told a step-by-step demolition very simple, I had a bad cell phone as he was taking off the surface.)

高通平台电信版CDMA手机写入MEID号码(Write MEID tool for Qualcomm platfrom)

说明：  正交频分复用（OFDM）信号的互补累计函数(ccdf_of_clipped_foltered_ofdm_signal)

说明：  横河CS3000培训讲义 DCS经典介绍和操作(Yokogawa CS3000 classical training, introduction and operation of DCS notes)

5G 网络 matlab 仿真 5G网络场景模拟 仿真 matlab代码，可运行(Matlab simulation of 5G network)

说明：  5. 在三条径的瑞利信道中，对于直接序列扩频： (1) 请设计DS-CDMA一种具体的码分导引辅助的信道估计方法，接收机分别采用等均益合并、最大比合并。用Simulink进行仿真，画出比特信噪比与信道估计均方误差的关系曲线和比特信噪比与误码率的关系曲线。 (2) 设频率已经同步，请设计DS-CDMA一种具体的单停顿滑动相关时间同步方法，用Simulink进行仿真，画出比特信噪比与捕获概率的关系曲线。 (3) 设时间已经同步，请设计DS-CDMA一种具体的频率同步方法，用Simulink进行仿真，画出比特信噪比与频率同步误差的关系曲线。(5. In three-path Rayleigh channel, for direct sequence spread spectrum: (1) please design a specific code division navigation aided channel estimation method for ds-cdma, and adopt equal-beneficial combination and maximum ratio combination for receivers respectively.Simulink is used to simulate and draw the relationship curve between bit SNR and channel estimation mean square error and the relationship curve between bit SNR and bit error rate. (2) assuming that the frequency has been synchronized, please design a specific single-stop sliding correlation time synchronization method ds-cdma, Simulink simulation, draw the relationship between the bit SNR and the acquisition probability curve. (3) if the time has been synchronized, please design a specific frequency synchronization method ds-cdma, Simulink simulation, draw the relationship between the bit SNR and frequency synchronization error curve.)

Bit Error Rate analysis of an Extended Receiver for Rectangular PAM. The performance of a digital communication system in the presence of additive white Gaussian noise (AWGN) can be assessed by the measurement of the bit error rate (BER). The Simulink model provided is a rectangular polar pulse amplitude modulation (PAM) baseband system with an AWGN channel and an extended sample and hold receiver with a low pass filter. An extended receiver has an odd number of sample and hold circuits. What remains to be answered is if such a receiver would provide a more desirable BER than that of a simple S/H receiver.