点云数据ICP

该程序主要是用于水准测量中水准数据的平差处理，精度较用平差易软件高(The procedure is mainly used for leveling leveling data in the adjustment processing, precision adjustment easy software)

风力发电机的模型，采用电力仿真软件设计，参数比较适合。(wind energy conversion system PSCAD)

框架剪力墙结构ansys软件APDL命令流，结构受力分析(Frame shear wall structure ansys software the APDL command-stream structural stress analysis)

A、名称：限幅滤波法（又称程序判断滤波法） B、方法： 根据经验判断，确定两次采样允许的最大偏差值（设为A）， 每次检测到新值时判断： 如果本次值与上次值之差<=A，则本次值有效， 如果本次值与上次值之差>A，则本次值无效，放弃本次值，用上次值代替本次值。 C、优点： 能有效克服因偶然因素引起的脉冲干扰。 D、缺点： 无法抑制那种周期性的干扰。 平滑度差。(A. Name: Limited filter method (also known as program judgement filter method) B. Method: Based on experience, the maximum allowable deviation (set to A) of two sampling times is determined. Judge each time a new value is detected: If the difference between the current value and the previous value is <=A, the current value is valid. If the difference between the current value and the previous value is greater than A, then the current value is invalid, abandon the current value and replace the current value with the last value. C. Advantages: It can effectively overcome the impulse interference caused by accidental factors. D. Disadvantages: That periodic interference cannot be suppressed. The smoothness is poor.)

ANSYS桥梁结构的桩土效应分析学习资料和实例文件(ANSYS pile soil effect)

可以实现电力系统负荷削减的判断,找出需要削减负荷的负荷点和母线编号(failed to translate)

地震解释处理matlab工具箱，由权威的CREWES小组发行，直接解压后复制到matlab的toolbox下就可使用(seismic interpretation Matlab toolbox, the authority issued CREWES group, unpacked directly copied to the Matlab toolbox can be used under)

BioSAR仿真程序，说明了干涉SAR仿真的基本条件和结果，初学者可以借鉴。(BioSAR simulation program, explains the basic conditions and the results of interferometric SAR simulation, beginners can learn.)

光伏控制器，自动充放电控制12V/10A光伏控制器（ERA-04-10-A）： 额定工作电压：DC12V 最大充电电流：10A 最大放电电流：5A/路（共两路负载） 太阳能组件开路电压：25V 空载电流：<15mA 温度补偿：-20Mv/°C 工作环境温度：-25°C～+50°C 使用海拔：<5500M 控制器尺寸（mm）: 光控电压（25°C）：<=3.3V 过放保护电压（25°C）：<10.8V 过放恢复电压（25°C）：>10.8V 过充保护电压（25°C）：>15.0V 过压保护电压：17.68V 过压恢复电压：14.7V 浮充电压（25°C）：13.4V～13.7V 恢复正常充电电压（25°C）：13.2V 结束正常充电电压（25°C）：15.0V (PV controller, automatic charge and discharge control 12V/10A PV controller (ERA-04-10-A): Rated voltage: DC12V Maximum charge current: 10A Maximum discharge current: 5A/Road (a total of two loads) Solar components of the open circuit voltage: 25V No-load current: < 15mA Temperature Compensation:-20Mv/° C Operating Temperature:-25 ° C ~+50 ° C with elevation: < 5500M Controller Size (mm): light control voltage (25 ° C): < = 3.3V over-discharge protection voltage (25 ° C): < 10.8V over-discharge recovery voltage (25 ° C):> 10.8V overcharge protection voltage (25 ° C):> 15.0V over-voltage protection Voltage: 17.68V overvoltage recovery voltage: 14.7V float voltage (25 ° C): 13.4V ~ 13.7V back to normal charging voltage (25 ° C): 13.2V end of the normal charging voltage (25 ° C): 15.0V)

说明：  多目标优化问题，主要用于城市供水优化调度(Multi-objective optimization, optimal scheduling for water supply)