button_irq

8bit nand flash interface for at91sam9263ek,其中编辑器为keil for mdk(8bit nand flash interface for at91sam9263ek, which editor for keil for mdk)

stm32F103 uart 2fifo接收通道，发送缓存大小自我修改(stm32F103 uart 2fifo Sending and receiving channel to set the size of the cache)

STC8和STC15系列选型，STC8和STC15系列选型(Selection of STC8 and STC15 Series)

stm32f1最小系统原理图及pcb图,有按键 ，串口，下载模块(Stm32f1 minimum system schematic diagram and PCB diagram)

说明：  FM1702射频芯片读写操作,主要用于IC卡读写操作(FM1702 RF chip to read and write operations)

由于工作中的需要，自己写的三星ARM S3C2440的BOOTLOADER，包含所有的工程文件。 最大特点：代码简单，易懂。 有三个功能：下载程序、烧写FLASH、初始化最小ARM板级环境(Because of work needs to write its own Samsung ARM S3C2440 of BOOTLOADER, contains all the project file. Most prominent feature: the code is simple, easy to understand. Has three functions: to download programs, programmer FLASH, initialize minimum ARM board-level environment)

The hardware driver for ST s STM32F4 series.

高精度相依模块芯片原理图资料以及使用方法还有手册(High-precision dependency module chip schematic data and the use of manual)

TI芯片AD115简介_中文资料_2012电子设计竞赛必备(TI chip AD115 Introduction _ Chinese data _2012 Electronic Design Contest essential)

STM32F0XX教程+例程源码 教程目录： 工程篇：搭建KEIL-MDK开发平台及制作MDK工程文件模板.pdf 资料篇-NUCLEO-072RB开发板特性讲解及资料准备.pdf 初级教程篇：按键(中断方式)实现24C04存储器内容读写.pdf 初级教程篇：实现一个LED灯(软件延时 systick定时器).pdf 中级教程篇：利用SPI总线构建NUCLEO-072RB和NUCLEO-302RB双机处理系统.pdf 中级教程篇：利用定时器实现6路互补PWM波形输出.pdf 高级教程篇：基于Labview上位机界面的NUCLEO-072RB数据采集系统.pdf 例程目录： 1.ADC 2.BLDC 3.DEMO-工程模板 4.EEPROM 5.KEY(中断方式) 6.KEY-EEPROM 7.LED（systick定时） 8.LED(软件延时) 9.PWM 10.SPI-MASTER-F0 11.SPI-SLAVE-F3 12.STM32-Labview-ADC 13.UART(printf 查询方式接收) 14.UART(中断方式方式接收)(STM32F0XX tutorial + routine source code Directory of courses: Project: building KEIL-MDK development platform and making MDK project document template.Pdf Information sheet -NUCLEO-072RB development board characteristics and data preparation.Pdf Primary tutorial: key (interrupt mode) to achieve 24C04 memory content read and write.Pdf Junior tutorial: realizing a LED lamp (software delay systick timer).Pdf Intermediate tutorial: using SPI bus to build NUCLEO-072RB and NUCLEO-302RB dual processor system.Pdf Intermediate tutorial: using timer to realize 6 complementary PWM waveform output.Pdf Advanced tutorial: NUCLEO-072RB data acquisition system based on Labview host computer interface.Pdf Routine Directory: 1.ADC 2.BLDC 3.DEMO- engineering template 4.EEPROM 5.KEY (interrupt mode) 6.KEY-EEPROM 7.LED (systick timing) 8.LED (software delay) 9.PWM 10.SPI-MASTER-F0 11.SPI-SLAVE-F3 12.STM32-Labview-ADC 13.UART (printf query mode) 14.UART (interrupt mode receive))