zigbee

用于有源电力滤波器的SVPWM控制模块仿真，内容详细可靠(For active power filter the SVPWM control module simulation, detailed and reliable)

ucgui LCD 驱动程序，包含常见的LCD控制器的驱动(ucgui LCD driver contains common LCD controller driver)

模拟BMS，测试充电桩，经测试完好！符合《GB-T 27930-2015 电动汽车非车载传导式充电机与电池管理系统之间的通信协议》，用的USB转CAN外接模块。(Analog BMS, charging pile test, tested good! In line with the communication protocol between the GB-T 27930-2015-board electric vehicle conductive charging unit and battery management system. )

LED64级亮度变化,占空比方式, 队列循环(failed to translate)

电子钟例程在MCS51上实现，用于proteus仿真软件(Electronic clock routine)

鼎科驱动板RTD2483 HDMI液晶屏程序(Dinke RTD2483 series HDMI LCD firmware)

单片机89C52控制点阵二极管，汇编语言编写(89C52 single-chip dot matrix control diodes, compiled languages)

说明：  113、基于51单片机老人生理智能监控GSM短信 本设计由STC89C52单片机电路+火焰传感器电路+加速度传感器+心率传感器电路+SIM800A_GSM模块电路+电源电路组成。 该系统实时监测老人是否跌倒，是否周围有火以及心率情况。 1、如果火焰传感器检测到火焰，则GSM向特定手机发送：Fire！ 2、如果ADXL345检测到老人跌倒了，则GSM向特定手机发送：Fall！ 3、如果心率传感器检测到老人心率高于120，则GSM向特定手机发送：High Heart！ 4、注意本设计一次上电上述情况每个只能触发一次上报短信，不会连续发送，防止反复发送，请放心使用。 5、短信处理过程有GSM信号灯指示。 6、GSM模块是SIM800A，该模块和SIM900A电路程序完全兼容外观外形一模一样。(GSM SMS for elderly physiological intelligent monitoring based on 51 MCU This design consists of STC89C52 MCU circuit + flame sensor circuit + acceleration sensor + heart rate sensor circuit + sim800a_ GSM module circuit + power supply circuit. The system monitors whether the elderly fall down, whether there is fire around and heart rate in real time. 1. If the flame sensor detects a flame, the GSM sends: fire! 2. If adxl345 detects that an old man has fallen, the GSM sends a specific mobile phone: fall! 3. If the heart rate sensor detects that the heart rate of the elderly is higher than 120, the GSM sends a message to a specific mobile phone: high heart! 4. Pay attention to the design of a power on, each of the above conditions can only trigger a report SMS, will not be sent continuously, to prevent repeated sending, please rest assured to use. 5. SMS processing process is indicated by GSM signal light.)

单片机实验软件之《按键识别》源程序，适用于电子，自控系专业期末答辩可选类型实验(SCM test software is " key identification" source for electronics, professional end of the respondent optional types of Automatic Control experiments)

说明：  此程序是LPC2119两路CAN程序 ，已经成熟用在产品上 并且很稳定(This program is CAN LPC2119 two procedures used in the product is mature and very stable)