-
regress
清华大学数学实验之一元与多元回归分析之幻灯片与MAT源码(Tsinghua University, one math test and multiple regression analysis element of the slide with the MAT-source)
- 2009-04-07 15:21:15下载
- 积分:1
-
Detection
the signal detection in the MC-CDMA system
- 2009-05-09 20:33:58下载
- 积分:1
-
CookieManagement
Project report of cookie mgmt
- 2011-02-13 23:51:27下载
- 积分:1
-
edgedetection
说明: 基于形态学的的玻璃瓶边缘检测,和canny算子对比,可出图。(Glass bottles based on morphological edge detection, and the canny operator compared to a map.)
- 2011-04-11 16:44:35下载
- 积分:1
-
MBinPSO
Modified binary PSO
PSO with mutation tools of genetic method combined
- 2014-11-17 08:22:20下载
- 积分:1
-
dtft
DTFT plot the spectrum of a sinusoidal signal
- 2015-03-03 02:33:13下载
- 积分:1
-
ai_RayCh
改程序主要对无线通信中的瑞利慢衰落通信信道进行了matlab仿真,可于仿真试验时进行调用。(Reform procedures for major wireless communications in the slow Rayleigh fading communication channel to carry out the matlab simulation, simulation tests can be carried out call.)
- 2007-12-22 19:56:50下载
- 积分:1
-
Learning
by this code you can distinguish circle from diamond in a 4*4 table...
this code is easy and understandable
enjoy it...
- 2010-12-26 15:28:28下载
- 积分:1
-
2D-band-gap
二维声子晶体带隙计算,XY色散关系计算,matlab编程(Two dimensional phononic crystals bandgap calculation, calculation of XY dispersion relation, matlab programming)
- 2014-12-09 11:11:30下载
- 积分:1
-
matlab
1. 给一段原始的语音信号(可以是自己录制的一段语音),加上一频率为3.8kHz的高频余弦噪声和频率为3.6kHz的高频正弦噪声(幅度自己可以选择),用窗函数设计一滤波器(要求最小阻带衰减为50dB)对加噪后的语音信号进行滤波,画出滤波器的频率响应曲线,画出滤波前后的时域图和频谱图。
需要用到的函数:
fir1 用窗函数设计FIR滤波器的函数
2. 用GUI设计一界面(如图1所示)完成如下功能:
1) 输入一语音信号,画出语音信号的时域图和频谱图;
2) 对语音信号加噪处理,画出加噪后的时域图和频谱图;
3) 给定滤波器的性能指标,采用几种不同的方法设计滤波器对加噪信后进行滤波,画出各滤波器的频率响应曲线,画出滤波后的时域图和频谱图。
(1. to some of the original speech signal (which can be a voice you record yourself), plus a cosine frequency of 3.8kHz frequency noise and frequency of 3.6kHz frequency sinusoidal noise (in the range that they can choose), with a window function to design a filter (requires a minimum stop band attenuation is 50dB) after adding noise to the speech signal is filtered, the filter frequency response curve to draw, draw diagrams and time-domain spectrum before and after filtering. Need to use the function: function fir1 with window function design FIR filter design 2. Using a GUI interface (Figure 1) complete the following functions: 1) an input speech signal, the speech signal in the time domain to draw graphs and spectrum 2) adding noise to the speech signal processing, draw diagrams and time-domain plus noise spectrum after 3) to set the filter performance, using several different methods designed to filter letter after adding noise filtering, draw the frequency response curve of each )
- 2015-01-09 10:00:04下载
- 积分:1