370511

（1）请推导出单径瑞利信道中的BPSK相干解调的理论误码率性能，并画出比特信噪比与误码率的关系曲线。 （2）在单径瑞利信道中，请设计一种时分的导引辅助的信道估计方法，用Simulink进行仿真，测量BPSK的误码率性能，画出比特信噪比与误码率的关系曲线，并与(1)的曲线进行对比。 ((1) derived from single-Path Rayleigh channel coherent demodulation of BPSK theoretical bit error rate performance and draw-bit signal to noise ratio and bit error rate curve. (2) in a single Path Rayleigh channel, please design a guided night-assisted channel estimation methods, using Simulink simulation, surveying BPSK BER performance, drawn-bit signal to noise ratio and bit error rate curve, and with (1) comparing the curve.)

数字调制解调信号ask fsk bpsk qpsk 16qam 64qam(digital modulation and demodulation )

基于matlab的mimo-OFDM仿真程序(Based on the mimo-OFDM matlab simulation program)

说明：  基于FPGA的16QAM调制解调设计，以及仿真实现(Design of 16QAM Modulation and Demodulation Based on FPGA)

采用加权网络中节点强度和权重都是幂率分布的模型，GPS和INS组合导航程序，做视觉测量的上位机代码。( Using weighted model nodes in the network strength and weight are power law distribution, GPS and INS navigation program, Do Vision Measurement PC code.)

1）设计Butterworth型音频抗混叠滤波器； 2）参数： 下通带频率300Hz；上通带频率3400Hz； 下阻带频率280Hz；上阻带频率3600Hz； 通带最大衰减0.3dB； 阻带最小衰减40dB； 3）采用一低通滤波器和一高通滤波器级联； 4）分别确定LPF和HPF的性能指标； 5）求出两滤波器的系统函数和频率响应，并画出其幅频特性曲线； 6）求整个滤波器的系统函数和频率响应，并画出其幅频特性曲线。(1) the design of Butterworth-type audio anti-aliasing filter 2) parameters: passband frequency of 300Hz on pass-band frequency 3400Hz under the stop-band frequency of 280Hz on stop-band frequency 3600Hz passband maximum attenuation of 0.3dB minimum stopband attenuation of 40dB 3) the use of a low-pass filter and a high-pass filter cascade 4) separately to determine the performance of LPF and HPF target 5) to derive two-filter system function and frequency response, and draw its increase frequency characteristic curve 6) for the entire filter system function and frequency response, and draw its amplitude-frequency characteristic curve.)

说明：  LED样例代码，原厂提供。凑够20个字才行吗？(Led sample code, provided by the original factory. Can you make up 20 words?)

8psk 数字解调器的simulink仿真(8psk digital modem s simulink)

从实际应用的角度出发，提出利用跟踪微分滤波器抑制机冀挠曲变形产生的影响，通过杆臂效应补偿消 除干扰加速度，用延时补偿算法减少由数据传输延迟造成的量测信息误差。在此基础之上，采用“速度+姿态” 匹配方案，研究了基于H_滤波估计的快速传递对准方法.大量数值仿真、静态试验、动态跑车试验表明，这 些方法有收敛速度较快、精度较高的特点，并t,有较强的抗干扰能力。试验也验证了传递对准方法的有效、可 行，能满足控制系统对导航信息的精度要求. ()

时变多径信道的matlab仿真（通过输入多普勒频移，时延变量等参数）(Multipath channel simulation)