functiongmodify

处理nc文件，生成grads用的ctl文件和数据(deal with netcdf file,and output the ctl file and data for the Grads software！)

simulates a wind turbine with a generation of asynchronous

tftb窗口，处理信号信息源程序，MATLAB(tftb window, signal processing information source, MATLAB)

yahoo股票历史数据下载器，matlab编写(yahoo stock historical data downloader, matlab write)

1、本程序用于仿真里德-穆勒（Reed-Muller）码在AWGN信道中的性能，调制采用bpsk 2、理论请参见《差错控制编码》（第二版），Shu Lin（美）编，晏坚等（译）一书P70-75.且仿真结果与书中图4-2完全一致 3、BPSK_AWGN_RM_Code.m为主程序，点击运行即可 4、The_creation_of_RM_code.m和RM_Decode.m分别为RM码的编、译码程序，而Majority_logic_decision.m用于译码中的大数判决，combine_dunction.m用于计算组合数。(1, the procedure for the simulation Reed- Muller (Reed-Muller) codes in AWGN channel performance, modulation using bpsk 2, theory, see " Error Control Coding" (second edition), Shu Lin (America) series , Yan Jian, etc. (translated) book P70-75., and the simulation results consistent with the book Figure 4-2 3, BPSK_AWGN_RM_Code.m-based program, click Run to 4, The_creation_of_RM_code.m and RM_Decode.m were RM compiled code decoding process, and in large numbers for decoding Majority_logic_decision.m judgment, combine_dunction.m used to calculate the number of combinations.)

说明：  AP算法源码代 运行可以画出图 AP算法源码代 运行可以画出图(AP algorithm source code to run on behalf of AP algorithm source code can be drawn diagram can be drawn map on behalf of running)

这个函数用于多目标跟踪数据关联，结合了最近邻数据关联个CJPDA数据关联算法，每个目标分配最多一个量测(This function is used for multi-target tracking data association, combined with nearest neighbor data association a CJPDA data association algorithm, each target allocation up to a measurement)

GPS/INS位置组合输出校正Matlab仿真 s_GPS_INS_position_ demo.m 组合主文件 kalman_GPS_INS_position_ NFb.m 卡尔曼滤波程序 ode500.mat 飞机飞行轨迹与INS输出数据 将三个文件放到同一个文件夹中，运行主文件即可。 (GPS/INS Position Combination Output Correction Matlab Simulation S_GPS_INS_position_ demo.m Combines the master file Kalman_GPS_INS_position_ NFb.m Kalman filter procedures Ode500.mat aircraft flight path and INS output data Will be three files into the same folder, run the main file can be.)

说明：  程序使用说明 1、所有仿真算法按章归类，文件中的程序名与书中一一对应。 2、将仿真程序复制到硬盘MATLAB运行的路径中，便可仿真运行。 3、本书算法在MATLAB 5.3版下运行成功，并适用于其他版本。 4、程序chap1_11.mdl；chap3_2.mdl；chap3_5.mdl；chap6_2.mdl；chap6_4.mdl需要在Matlab6.5下运行，特此说明。 5、假如您对仿真程序有疑问，请及时通过 E-mail 与作者联系。 北京航空航天大学 刘金琨 E-mail 地址： ljk@dept3.buaa.edu.cn或ljk@buaa.edu.cn(Program instructions 1 All simulation algorithms are classified by chapter, and the program name in the file corresponds to that in the book one by one. 2 Copy the simulation program to the Matlab running path of the hard disk, then the simulation can run. 3 The book algorithm in Matlab version 5.3 run successfully, and suitable for other versions. 4 Program chap1.11.mdl; chap3.2.mdl; chap3.5.mdl; chap6.2.mdl; chap6.4. MDL needs to run under MATLAB6.5. 5 If you have any questions about the simulation program, please contact the author by e-mail.)

自己编写的BDPSK调制与解调，内含matlab-figure-file、matlab-M-file和得出的jpg格式图形！(I have written BDPSK modulation and demodulation, containing matlab-figure-file, matlab-M-file and come to the jpg format graphics!)