PVModel

说明：  基于动态手势识别的人机交互技术研究——硕士论文(Dynamic gesture recognition based on human-computer interaction technology- pp)

Understanding the Software Communications Architecture

在matlab环境下，编程实现用拉普拉斯算子改善图像的反差增强程序(In the matlab environment, programming with Laplacian to improve image contrast enhancement procedure)

matlab中的svm工具包，是标准化的svm算法，只能用于线性问题，非线性的需用libsvm或lssvm来解决。(svm in matlab Kit, standardized svm algorithm can only be used for linear problems, nonlinear the required libsvm or lssvm of resolve.)

说明：  MATLAB确定几何边界区域函数，用来计算偏微分方程的部分计算源代码(MATLAB sure geometry region function is used to calculate the boundary, partial differential equations of the calculation source code )

there is a matlab cod for computing Arnold Tongue in Hodgkin-Huxley model,and it occur when we have synchronization.This model is famous in neuroscience.

wireless communication 5g OFDM

有限元求解possion方程的matlab代码(Finite Element Analysis of Possion equation matlab code)

用局部参数最优化方法设计一个模型参考自适应系统,可调增益的初值Kc(0)=0.2，给定值r(t)为单位阶跃信号，即r(t)=A×1(t)。 要求： 1把连续系统离散化(采样时间可取0.1)。 2编制并运行这个系统的计算机程序(注意调整B值，使系统获得较好的自适应特性)。 3记录ym、yp的曲线 记录kp×kc的曲线 记录广义输出误差e的变化曲线。 4在参数收敛后，让Kp=2变为Kp=1，重新观察Kp×Kc及e的变化曲线。 5找出在确定的B值下，使系统不稳定的A值(阶跃信号的幅值)，并与用劳斯稳定判据计算的结果比较。 (With local parameter optimization method to design a model reference adaptive system, adjustable gain initial Kc (0) = 0.2, for a given value of r (t) for the unit step signal that r (t) = A × 1 ( t). Requirements: a continuous system discretization (sampling time of 0.1 preferred). 2 compiled and run the system computer program (Note B to adjust the value of the system to obtain better adaptive characteristics). 3 records ym, yp curve record kp × kc curve records generalized output error e curves. 4 parameter convergence, let Kp = 2 into the Kp = 1, re-observed Kp × Kc and e curves. B-5 to find value in determining the next, making the system unstable A value (step signal of amplitude), and using Routh stability criterion and the comparison of the results calculated.)

matlab海浪模拟程序文中的两个word分别是在二维和三维下海浪的波形图（有所提供的matlab源程序生成） bopu.m是标准的p-m谱，输入风级数和频率数得到该风级下的p-m谱 erweihailangboxing.m是生成三维海浪波形的源程序，输入风级数，频率数和角度数得到该风级下的海浪波形； hailangboxing.m是生成二维海浪波形的源程序，输入风级数和频率数得到该风级下的海浪波形； SDwave.m是分形法所用的源程序，与本线性得加法所采用的 方法不一样。。纯属我毕设的客串。。所得波形为二维的海浪。(wave matlab simulation program)