simulateur

说明：  前已提出的频谱感知方法主要包括匹配滤波器检测、 能量检测、 循环平稳特征检测以及多分辨率频谱感知. 这些方法均为单节点感知方法.然而，在阴影和深度衰落情况下， 单个节点的感知结果并不可靠， 因此， 需要对多个节点的感知结果进行融合，以提高检测可靠性， 即协作感知技术. 文献采用“或” 准则对各个 CR 感知结果进行融合. 文献则提出了基于 D-S 证据理论的协作频谱感知算法，虽然该算法的性能比“或” 准则或“与”准则要好， 但需要存储大量历史信息， 算法的计算复杂度也很高. 文献中分析了采用似然比检测(likelihood ratio test， LRT) 的软判决与采用“与” 准则的硬判决的性能， 结果表明采用软判决的协作感知性能更优(Previously proposed spectrum sensing methods mainly include matched filter detection, energy detection, cyclostationary feature detection and multi-resolution spectrum sensing. These methods are all single node sensing methods. However, in the case of shadow and deep fading, the sensing results of single node are not reliable, so, It is necessary to fuse the sensing results of multiple nodes to improve the detection reliability, i.e. cooperative sensing technology. In the literature, "or" criterion is used to fuse the CR sensing results. In the literature, a cooperative spectrum sensing algorithm based on D-S evidence theory is proposed. Although the performance of the algorithm is better than "or" criterion or "and" criterion, a large amount of historical information needs to be stored, The computational complexity of the algorithm is also very high. In the literature, the performance of the soft decision based on the likelihood ratio test)

说明：  相干光通信QPSK，QAM调制格式等MATLAB仿真代码，直接运行即可，非常好用。(Coherent optical communication QPSK, QAM modulation format matlab simulation code, direct operation can be, very easy to use.)

说明：  瑞利信道下的盲源分离算法可以实现干扰信号和源信号的有效分离(Blind source separation algorithm in Rayleigh channel)

大规模MIMO信道容量仿真，研究毫米波预编码的可以相互探讨(Massive MIMO capacity)

采用滤波器组，将盲分离与声源定位结合在一起。滤波器组中分别进行子带处理，并且在每个子带中进行声源定位，最后综合所有子带估计的方向得到多个声源的方位信息，同时将声源信息作为ICA分析的约束条件，可以在色噪声及多得到更好的盲分离效果。其优势在于用滤波器组进行多次的估计声源方向，再加以合适的权值均衡后即可得到更优的估计。(The use of filters will be blind source separation and sound localization together. Filter group were sub-band treatment, and in each sub-band in Sound Source Localization, and finally all the sub-band is estimated to be more than the direction of sound source location information, as well as sound source information as ICA analysis of the binding conditions, colored noise can be better and many of the blind source separation effect. Its advantage lies in a number of filter banks with estimated sound source direction, coupled with an appropriate balance weights can be obtained after the better estimate.)

基于MATLAB平台的通信系统的仿真，RS编码，OFDM调制，加入PLC信道噪声，并进行误码率的检测，运行无误，程序完整。(MATLAB-based communications system simulation platform, RS coding, OFDM modulation, adding PLC channel noise, and make BER testing, run correctly, the program integrity.)

说明：  prodave是西门子PLC与高级语言的程序接口,如何使用它,这里给出一个VC与西门子PLC通讯并读写DB块数据的例子(Prodave is Siemens PLC and high level language program interface, how to use it, so here is a VC and Simon PLC and literacy DB block of data example )

说明：  截获接收机采用时频分析进行跳频通信的参数估计程序(Intercepting the parameter estimation procedure of the receiver for time-frequency analysis for frequency hopping communication)

利用matlab自适应滤波器实现心电信号的去噪 自适应滤波器 心电图(De-Noising of Electrocardiogram (ECG) with Adaptive Filter Using MATLAB)

传输屏幕到远程电脑并显示,很不错的易语言源码,易爱好者可以下载使用()