nsgmajmv

自动化应用－－直流电动机和交流发电机控制系统设计，环境为MATLAB(automation applications-- DC motor and alternator control system design environment for MATLAB)

说明：  CS经典算法，MP重构算法的实现。网上很少有地方可以下到哦！(CS classical algorithm, MP reconstruction algorithm. There are few places online you can downloaded now!)

典型的粒子群算法的matlab程序，附带详细注释(typical PSO algorithm with detailed annotation )

块自适应处理算法先有采样快拍数据计算采样协方差矩阵，再来计算自适应权矢量。典型的块自适应处理算法为采样矩阵求逆(SMI)算法。仿真了采样矩阵求逆法(SMI)的波束形成方向图旁瓣的高低受信号快拍数的影响。(Block adaptive processing algorithms prior sample snapshot data of the sampling covariance matrix, again computing adaptive weight vector. A typical block adaptive processing algorithms for the sample matrix inversion (SMI) algorithm. Simulation of the sampling matrix inversion method (SMI) beamforming pattern sidelobe level of the signal by the number of snapshots.)

一个用matlab实现的基于图像灰度概率分布的图像模糊增强算法，本人已使用。(using a Matlab-based images to achieve the probability distribution of gray fuzzy image enhancement algorithms, I have to use.)

说明：  SAR 信号处理中常用的带频移的傅里叶变换函数，可以直接对信号进行处理(SAR fft transform with fftshift)

利用ccs环境、MATLAB环境、DSP（TMS320F2812)、被测对象和Agilient网络分析仪E5071B，构建一个自动测量系统。 相信大部分人都知道基于NI公司的GPIB总线，可以实现自动测量，但NI公司的方案实在太昂贵，采用MATLAB能够大大降低成本。matlab与ccs之间基于RTDX协议进行数据交换，同时matlab基于TCP/IP协议与E5071B之间通信，源码说明如下： （1）RTDX_ok目录：matlab7.0代码，包含了一个用GUI实现的界面和相关的具体代码，特别是在其中实现了SCPI语言来对仪器进行控制。 （2）TMS320F2812目录：包含ccs下的c代码，如果没有做过RTDX的应用，相信这个对你很有启发。(Use ccs environment, MATLAB environment, DSP (TMS320F2812), the measured object and Agilient network analyzer E5071B, construct an automatic measurement system. I believe that most people are aware NI' s GPIB-based bus, you can realize automatic measurement, but NI' s program is too expensive, the use of MATLAB can greatly reduce costs. ccs between matlab and RTDX protocol-based data exchange, while matlab based on TCP/IP protocol and communication between the E5071B, the source described as follows: (1) RTDX_ok directory: matlab7.0 code, contains a GUI implementation with the interface and specific code, especially in one of implementation of the SCPI language to control the apparatus. (2) TMS320F2812 directory: contains ccs of c code, if not done RTDX application, then I think it was very instructive for you.)

实现不敏卡尔曼滤波,可以用于雷达目标跟踪，多传感器数据融合等等！！！(this matlab program gieves the UKF)

使用matlab自己编写的pca+lda方法，大家一起分享(pca and lda in matlab by myself,we will share together)

说明：  matlab主成分分析代码，可直接修改参数即可运用于建模(Matlab principal component analysis code)