登录
首页 » matlab » QPSK定时同步代码,采用Gardner定时同步算法 qpsk_demod

QPSK定时同步代码,采用Gardner定时同步算法 qpsk_demod

于 2021-02-03 发布 文件大小:1KB
0 476
下载积分: 1 下载次数: 50

代码说明:

  QPSK定时同步代码,采用Gardner定时同步算法,Farrow插值算法(QPSK timing synchronization code, using Gardner timing synchronization algorithm, Farrow interpolation algorithm)

文件列表:

qpsk_demod.m, 3270 , 2017-11-17

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • antenna_selection_massive_MIMO-master (1)
    说明:  大规模MIMO中采用天线选择来降低系统复杂度和成本,其中包括最优天线选择和递减天线选择,快速天线选择和基于范数的天线选择算法。(Antenna selection is used in large-scale MIMO to reduce system complexity and cost, including optimal antenna selection and decreasing antenna selection, fast antenna selection and antenna selection algorithm based on norm.)
    2021-04-24 13:48:47下载
    积分:1
  • p200602-701
    huong dan lap trinh bang labview
    2010-11-14 13:00:48下载
    积分:1
  • LDPC
    说明:  实现LDPC信道码的仿真,已在大型软件开发项目中实用(LDPC code and decode matlab)
    2020-11-30 16:47:58下载
    积分:1
  • 16QAM系统
    16QAM信号在高斯信道与瑞丽信道下的调制解调,误码率计算(Modulation and demodulation of 16QAM signals in Gaussian channel and Rayleigh channel, calculation of bit error rate)
    2019-01-12 11:44:13下载
    积分:1
  • SRC
    说明:  最大限度地平 FIR 逼近 (拉格朗日插值法) 拉格朗日插值是一种时域方法,导致基于多项式的筛选器的一个特殊情况。用 M 次多项式近似表示输出信号。最简单的情况 (M = 1) 对应于线性插值。让我们设计和分析将通过各种馏分拆分单元延迟的几种线性分数时滞滤波器:(Maximally-Flat FIR Approximation (Lagrange Interpolation) Lagrange interpolation is a time-domain approach that leads to a special case of polynomial-based filters. The output signal is approximated with a polynomial of degree M. The simplest case (M=1) corresponds to linear interpolation. Let's design and analyze several linear fractional delay filters that will split the unit delay by various fractions:)
    2017-08-20 11:31:08下载
    积分:1
  • dpd_simulation_matlab
    qpsk调制 预失真仿真程序 基于matlab开发环境( LUT predistortion matlab simulation)
    2012-05-06 15:27:22下载
    积分:1
  • BICM_8PSK_AWGN
    bit interleaved coded modulation Performance in AWGN for different trellises
    2011-11-29 14:24:18下载
    积分:1
  • 搭建BPSK+码+交织仿真信链路
    说明:  搭建 BPSK+编码+交织仿真通信链路,仿真分析在不同信道条件下的不同译 码算法的误比特率性能。基于 matlab,搭建 BPSK+卷积编码+交织通信收发链路, 仿真参数如下: 1) 信源比特速率: 100 b R kbps = 2) 卷积编码:码率为 1/2,生成多项式为(561,753) 3) 译码方式:维特比译码(硬判决译码、软判决译码(8 比特量化)) 4) 交织:行列交织,交织器深度为 100bit,宽度为 10; 5) 仿真点数:106 1. 在 AWGN 信道下,仿真并绘出该系统在硬判决和软判决(3bit 量化)两 种译码方式下的信源误比特率曲线,并进行分析。 2. 设定某种交织器结构,在单径瑞利衰落信道( 100 d f Hz = )下,采用理 想信道估计,仿真并绘出该系统在有无交织、不同译码方式(硬判决和 软判决)时,在不同 0 b EN下的信源误比特率曲线,并进行分析。 3. 改变交织器结构,选择三种不同的交织深度(自行决定),在单径瑞利衰 落信道( 100 d f Hz = )下,仿真并绘出该系统在不同交织长度时,在不 同 0 b EN下的信源误比特率曲线,并进行分析。(Build a BPSK + encoding + interleaving simulation communication link, and analyze the different translations under different channel conditions The bit error rate performance of the code algorithm. Based on MATLAB, BPSK + convolutional coding + interleaved communication transceiver link is built, The simulation parameters are as follows: 1) source bit rate: 100 b r Kbps = 2))
    2020-05-15 12:24:37下载
    积分:1
  • mygmsk1
    这是一个关于gmsk和msk性能分析比较的源程序,能很好的实现GMSK频谱和功率谱。(this a matlab program about gmsk and msk s dpinpu and gonglvpu.)
    2020-07-02 02:00:02下载
    积分:1
  • RMSE变化tls-esprit
    说明:  详细介绍了基于均匀线阵型的波达方向估计算法,线性旋转不变性子空间方法tls-esprit,介绍了RMSE变化的情况,具有可操作性。(Introduces the DOA estimation algorithm based on uniform linear array in detail, the linear rotation invariant subspace method (tls-esprit), the changes in RMSE and it is operable.)
    2020-05-26 23:11:13下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载