基于LABVIEW的登录程序

说明：  labview学习资料，花了2W获得的过程学习资料，可以看看很多小例程，值得学习！(LabVIEW learning materials, spent 2W to get the process of learning materials, you can see a lot of small routines, worth learning!)

KNR的电机驱动与控制，实现电机的正反转，读取编码器的读数，设置电机的速度，读数位置。 需要有KNR（贝登堡公司生产）(With the KNR driver control motor, to achieve positive motor, read the encoder readings, set the speed of the motor, reading position. The need for KNR (Baden Powell company))

labview实现神经bp网络,无需进入其他程序，在labview中就能运行(LabVIEW realizes neural network)

说明：  基于labview的modus通信，接受和发送数据，产生报文(digital received and sent)

说明：  基于Labview程序的HEX文件解析程序，可以基于此进行程序改进，编写程序下载上位机(Based on the hex file analysis program of LabVIEW program, the program can be improved, and the program can be written to download the upper computer)

1．采用Labview设计一虚拟函数信号发生器， 通过数据采集卡输出波形信号，调节信号的相关参数，可观察示波器上波形的变化情况。 ⑴ 以NI MyDAQ数据采集卡作为输出接口； ⑵ 数据采集卡输出多种信号，至少完成三种波形：正弦波、三角波、方波(可调占空比)的输出，同时前面板上显示各输出波形； ⑶ 频率、幅值、初相位、直流偏移量和方波的占空比（0～100 ）等参数可以通过前面板控件调节。 ⑷ 前面板可显示输出波形。(1. Labview design using a virtual function signal generator, data acquisition card output waveform signal, adjust the relevant parameters of the signal can be observed on an oscilloscope waveform changes. ⑴ with NI MyDAQ data acquisition card as output interface ⑵ data acquisition card output a variety of signals, to complete at least three waveforms: sine wave output, triangle wave, square wave (adjustable duty cycle), while each of the output waveform is displayed on the front panel ⑶ frequency, amplitude, initial phase, the DC offset and duty cycle square wave (0 to 100 ) and other parameters via the front panel controls to adjust. ⑷ output waveform can be displayed on the front panel.)

基于LabVIEW软件编写，利用二维卷积实现图像边缘检测。(Written based on LabVIEW software, the use of two-dimensional convolution image edge detection.)

裴波拉那齐数列前一百项求和，利用while循环等(Pei Qi sequence that summed Bora Fibonacci)

给出百分制成绩，要求输出成绩等级，90分及以上为A，80分至89分为B，70分至79分为C，60至69分为D，59分及以下为E，小于0分或者高于100分弹出错误提示框。(Given percentile scores, the required output Grade, 90 points and above for A, 80 to 89 are divided into B divided into C, 70 to 79, 60 to 69 is divided into D 59 and for E < 0 or higher than 100 pop-up error message box.)

西门子1200与labview通过以太网通信，包括 PLC和labview 的全套程序及使用说明，本人亲测能用，欢饮下载！(Siemens 1200 communicates with LabVIEW through ethernet, including the complete program of PLC and LabVIEW and the instructions of use. I personally test the usage and download it with pleasure!)