UMTS_Access2009

数字基带系统将数字信号从时域上看时数字滚降，需要画出滚降前后的波形展示出来。频域上带宽变化了。输入滤波器之前的波形与采样判决之后的波形。采样判决前的频谱。 采样判决后的码型。 2、眼图（采样判决之前的眼图）（信噪比大眼图清晰） 3、误码曲线，（横坐标时信噪比，纵坐标时误码率） 4、Arfa变化对误码特性的影响，变好还是变差(变好)，眼图清晰度变化（清晰），传递函数的带宽的变化。（带宽越大）(1.Digital baseband system point of view the digital signal from the time domain when the number of roll-off, you need to draw the waveform displayed before and after the roll-out. The frequency domain, the bandwidth change. Input filter and sample ruling before the wave after wave. Sample pre-judgment spectrum. Sampling pattern after the verdict. 2, the eye diagram (eye before sampling decision) (SNR big eye clear) 3, the error curve (abscissa when the signal to noise ratio, bit error rate when the vertical axis) 4, Arfa impact of change on BER performance, get better or worse (getting better), change of eye-definition (clarity), the transfer function of the bandwidth changes. (The greater the bandwidth))

flash website template by Namira - gallery

Designing a bandpass and bandstop filter using matlab.

说明：  设计一个理想通信系统，实现信息字符流的传输。 发射器： <1>将消息（字符串形式）编码成一个符号序列； <2>用脉冲成形将串符号序列转变成模拟脉冲信号； <3>将模拟脉冲信号调制到载波信号上。 接收器： <1>对接收的信号进行采样； <2>解调信号成基带信号； <3>将信号恢复成字符串。(Design an ideal communication system, the realization information transmission of character flow. Emitters: < 1 > will news (string form) coding into a symbol sequence < 2 > by using a pulse forming will string of symbols into a simulation pulse signal sequences < 3 > will simulate the pulse signal modulation to carrier signal. Receiver: < 1 > of received signal sampling < 2 > demodulation signal into baseband signal < 3 > will signal back into a string.)

how to calculate 2D power delay profiles

its the source code for face protected system

Mass spring damper model

这是我在做浅海水声信道建模时收集的一些资料和程序，有一定的参考价值，分享给大家(This is some of the information and procedures I was doing shallow water channel modeling the collection, there is a certain reference value for everyone to share)

一个运用matlab程序源码，进行模糊PID设计 完整源码。(A program source code using matlab, the fuzzy PID design a complete source code.)

负责火星的一个低轨道空间站的设计。为简化结构，该空间站由一系列密闭的立方体（airtight cubical modules ACM）组成，这些ACM曾连接在一起。困扰你的一个问题是致命的病菌也许留在火星的上层大气中。因为空间站有时需要在上层大气中飞行，所以急需在ACM的各个接触面进行额外的防护，无论是边对边还是面对面，连接是密闭的，所以没有细菌能够进入。一个ACM与另外一个ACM共享的面不需要防护。如果在每个ACM每个面上都加防护，花费巨大。因此，需要知道ACM额外防护的确切面数目(Responsible for the design of a low-orbit space station on Mars. In order to simplify the structure of the space station by a series of closed cubes (airtight cubical modules ACM) composed of these ACM had together. One problem is bothering you deadly germs might stay in the upper atmosphere of Mars. Because the station is sometimes necessary to fly in the upper atmosphere, so urgently needed in all contact surfaces of the ACM additional protection, either face to face or side-to-side, the connection is closed, so no bacteria can enter. An ACM ACM shared with another surface does not need protection. If you have added protection on each side of each ACM, costly. Therefore, the need to know the exact number of additional surface protection ACM)