CSTcode

用来仿真fsk PSK 误码率用来仿真fsk PSK 误码率(simulate the ber of fsk and psk)

【谷速软件】matlab修改-DTFT 可以用着参考使用 ([Valley] matlab speed software can be used to modify the reference use-DTFT)

运用dds改进型算法 cordic算法实现将三角函数旋转任意角度的matlab代码(Using cordic to realize the manipulation of sin or cos function, which is changing their current phase into any given phase.)

MAKELATT Create lattice L = MAKELATT(KIND,PTS,DIM) makes desired kind of dim-dimensional finite lattice that consists of pts elements. Available designs are listed in the table below. All the generated lattices are geometrically uniform. The lattice points are chosen from the origin to higher shells. Sometimes its usefull to generate lattices from the number of one dimensional pattern side i.e. PTS = DIM ^ SIDE. Table of available designs Design | Dimension | KIND -----------+-----------+---------- Zn | n>=1 | Z An | n>=1 | A Dn | n>=3 | D Hexagonal | n=2 | Hex fcc | n=3 | fcc

matlab编写,eeglab软件(Matlab prepared eeglab software)

说明：  这是一个计算两个点源之间由于光力的程序。(This Program calculates tansverse Optical Force in two point sources. )

混合罚函数法，结合了外罚函数法和内罚函数法的有点，适用于matlab程序(Mixed penalty function method, a combination of external and internal penalty function method a little penalty function method for matlab program)

这个M文件产生了一个以T为周期，来自于经验估计信道的噪声信号，并且仿真了最新的自适应盲均衡恒模算法。(These M-files generate received noisy signals from empirically-measured channels and simulates a blind adaptive equalizer updated with Constant Modulus Algorithm)

SM系统matlab程序，传输天线、接收天线数量可调，信号调制方式可调，循环次数可调。最后生成BER性能曲线，并将不同SNR下的BER数据存储到mat文件中。(SM system matlab program, the number of transmission antennas, a receiving antenna is adjustable, adjustable signal modulation scheme, the number of cycles is adjustable. Last generate BER performance curve, and store data in different SNR BER under the mat file.)

第一步是计算输人信号单边功率谱密度（ESD）。使用快 ％速傅里叶（FFr）算法将信号从时域转换到频域。因为FFr算法的输出是离散谱，而这 ％里我们需要的是连续谱，因此需要引人不同的比例因子来实现从离散谱到连续谱的转换。 ％在第二步中，我们利用迭代算法计算出相对于特定阂值的ESD的最高和最低频率，从而 ％估算出被检测信号所占用的带宽。这种算法同时适用于基带信号和已调制信号。最后， ％在第三步中，我们给出了输出图形的原代码。(The first step is calculating the input signal unilateral power spectral density (ESD). The use of fast Fourier speed (FFr) algorithm for the signal conversion from time domain to frequency domain. FFR algorithm because the output is a discrete spectrum, which we need is a continuous spectrum, so the need for food of different scale factor to achieve from the discrete spectrum to continuous spectrum conversion. In the second step, we use iterative algorithm to calculate a specific threshold in relation to the ESD of the highest and lowest frequency, thus estimated to be occupied by the signal detection bandwidth. This algorithm applies to both baseband signal and modulation signals. Finally, in the third step, we give the graphical output of the original code.)