毕业设计stm32f1最小系统原理图及pcb图

这是应用于 windows ce 4.2平台上串口接受的程序，我已经实践过，好用，也可以根据它修改出发送程序(This is used in windows ce 4.2 platform serial port to accept the procedure, I had already been put into practice, use can also be sent out according to its modified procedures)

说明：  RTL8367RB的datasheet，主要用于无管理交换机的以太网交换芯片(datasheet for RTL8367RB)

STM32的CAN通信接收程序，在STM32F103ZET6板子上测试通过。。(STM32 CAN RX Demo code)

Patch to add iMX27ADS support to Openembedded written by acassis at gmail dot com

基于STM32和W5500，W5500作为DHCP客户端，路由器作为DHCP服务器，W5500发送广播包获取IP地址。(Based on STM32 and W5500, take W5500 as a DHCP client，take router as a DHCP server, router. W5500 sends a broadcast packet to obtain IP address.)

STM32F0XX教程+例程源码 教程目录： 工程篇：搭建KEIL-MDK开发平台及制作MDK工程文件模板.pdf 资料篇-NUCLEO-072RB开发板特性讲解及资料准备.pdf 初级教程篇：按键(中断方式)实现24C04存储器内容读写.pdf 初级教程篇：实现一个LED灯(软件延时 systick定时器).pdf 中级教程篇：利用SPI总线构建NUCLEO-072RB和NUCLEO-302RB双机处理系统.pdf 中级教程篇：利用定时器实现6路互补PWM波形输出.pdf 高级教程篇：基于Labview上位机界面的NUCLEO-072RB数据采集系统.pdf 例程目录： 1.ADC 2.BLDC 3.DEMO-工程模板 4.EEPROM 5.KEY(中断方式) 6.KEY-EEPROM 7.LED（systick定时） 8.LED(软件延时) 9.PWM 10.SPI-MASTER-F0 11.SPI-SLAVE-F3 12.STM32-Labview-ADC 13.UART(printf 查询方式接收) 14.UART(中断方式方式接收)(STM32F0XX tutorial + routine source code Directory of courses: Project: building KEIL-MDK development platform and making MDK project document template.Pdf Information sheet -NUCLEO-072RB development board characteristics and data preparation.Pdf Primary tutorial: key (interrupt mode) to achieve 24C04 memory content read and write.Pdf Junior tutorial: realizing a LED lamp (software delay systick timer).Pdf Intermediate tutorial: using SPI bus to build NUCLEO-072RB and NUCLEO-302RB dual processor system.Pdf Intermediate tutorial: using timer to realize 6 complementary PWM waveform output.Pdf Advanced tutorial: NUCLEO-072RB data acquisition system based on Labview host computer interface.Pdf Routine Directory: 1.ADC 2.BLDC 3.DEMO- engineering template 4.EEPROM 5.KEY (interrupt mode) 6.KEY-EEPROM 7.LED (systick timing) 8.LED (software delay) 9.PWM 10.SPI-MASTER-F0 11.SPI-SLAVE-F3 12.STM32-Labview-ADC 13.UART (printf query mode) 14.UART (interrupt mode receive))

Boot Loader for Robot Arm from Arexx, usable to flash the uC. The Boot Loader requires java.

说明：  用stm32f10x实现can和串口通信功能(use stm32 can to usart)

ARM9开发裸机程序 2440之i2c操作(ARM9 development program 2440 i2c bare metal operating)

基于51单片机的电能表软件设计，电能测量芯片是ATT7022C，有完整的读写和校表程序，已通过测试。(SCM based on the 51 Meter software design, power measurement chip ATT7022C, and write a complete calibration procedures, it has been tested.)