LabVIEW波形求导

本系统可做自动控制原理中的时域分析仿真实验，系统特性如下： 1：可选择仿真系统为一阶、二阶、任意阶 2：可选择信号源为正弦波、三角波、锯齿波、方波（可模拟阶跃信号），并可调节信号源频率、幅值、相位、偏移、方波占空比 3：可选择信号采样率及采样数 4：自动计算传递函数 5：自动计算时域响应参数（增益系数、上升时间、峰值、峰值时间、稳定时间、超调量） 6：波形图同时显示原始信号和响应信号 注：使用本系统需安装labview控制设计与仿真库(The system can do automatic control theory in the time-domain analysis simulation, the system behaves as follows: 1: simulation system can be selected for the first, second, any order 2: select the signal source is a sine wave, triangle wave, sawtooth, square wave (analog step signal), and can adjust the signal source frequency, amplitude, phase, offset, duty cycle square wave 3: the the optional signal sampling rate and the number of samples 4: automatic calculation of the transfer function 5: Automatic calculation domain response parameters (gain coefficient, rise time, peak, peak time, settling time, overshoot) 6: waveform diagram shows both the original signal and the response signal Note: Use the system to be installed LabVIEW Control Design and Simulation library)

非常好用的通讯转换，用于rs232，十六进制十进制转换(Very easy to use communication converter for rs232, hexadecimal decimal conversion)

比例谐振（PR）控制在逆变电源中的仿真，控制器采用PR控制器，电压外环，电流内环的LABVIEW仿真。输出115V/400Hz交流电( U6BD4 u4F8 u8C0 u632F uFF08PR uFF09 u63A7 u5236 u5728 u9006 u53D8 u7535 u6E90 u4E2D u7684 u4EFF u771F uFF0C u63A7 u5236 u5668 u91C7 u7528PR u63A7 u5236 U5668 uFF0C u7535 u538B u5916 u73AF uFF0C u7535 u6D41 u5185 u73AF u7684LABVIEW u4EFF u771F u3002 u8F93 u51FA115V/400Hz u4EA4 u6D41 u7535)

电机控制，位置控制，速度控制，反馈控制/..............(motion control)

说明：  数据采集卡采集拉力值，与预先设定的拉力值进行比较，然后PID运算，控制相应的PWM占空比输出，最终控制电机的速度(The data acquisition card collects the pull value and compares it with the pre-set pull value. Then the PID arithmetic is used to control the output of the corresponding PWM duty cycle, and finally the speed of the motor is controlled.)

说明：  LABVIEW的BP神经网络曲线拟合程序(the BP ANN exe based on LABVIEW )

建议实现BP神经网络的Labview程序，主要还是用做学习，工程实际还有所欠缺(We recommend implementing programs Labview BP neural network, learning is mainly used in engineering practice are lacking)

对（极值域均值经验模态分解）EMMD算法的实现(Implementation of EMMD algorithm)

说明：  《我和+LabVIEW》示例程序 Sample Program of "I and + LabVIEW"(Sample Program of "I and + LabVIEW")

基于LabWindows CVI的界面编程。数据解析显示，指令下发(LabWindows CVI )