-
motor-control-system-in-Labview
Labview 源码，实现永磁电机控制上位机控制，与dsp2812配合使用，主要用于发出控制信号和接收状态信号。(it is programmed in labview and it is for controlling a BLDC combined with dsp2812. it is mainly used for send control signal s and recieve state signals.)
- 2017-01-15 16:48:02下载
- 积分：1
-
手把手教你在LabVIEW下使用OPC
说明： Labview OPC和欧姆龙PLC通讯(LabVIEW OPC and OMRON PLC communication)
- 2020-03-04 19:39:21下载
- 积分：1
-
ocean spectrometer
用于读取ocean光谱仪的光谱数据、保存光谱数据至tdms文件、并通过daq设备输出对应的模拟电压。
（需要安装ocean光谱仪驱动、daq-mx驱动）(Used to read spectral data of ocean spectrometer, save spectral data to TDMS file, and output corresponding analog voltage through DAQ device.)
- 2017-07-28 11:35:11下载
- 积分：1
-
关于LabVIEW的一些程序
伺服电机控制 Modbus命令帧生成程序. 波形记录 数据的采集与显示 串口通讯 PID控制(Servo motor control. Modbus command frame generation program. Waveform recording. Data collection and display. Serial communication. PID control.)
- 2018-03-01 12:04:12下载
- 积分：1
-
The-sound-tech-based-on-Labview
基于Labview的声音检测技术CAA文献，可鉴别人声，运用了Matlab小波分析。(Labview-based voice detection technology CAA literature, can identify the human voice, the use of Matlab wavelet analysis.)
- 2014-05-10 09:39:39下载
- 积分：1
-
测试
说明： labview实现串口示波器的功能，读取示波器发送的浮点数数据，并绘制曲线(Serial port oscilloscope)
- 2019-10-23 13:37:02下载
- 积分：1
-
labview-function-creation
函数发生器，各种常规的波形发生，以及数据的存储和数据导入功能！(Function generator, a variety of conventional waveform generation, and data storage and data import capabilities!)
- 2013-10-18 22:50:22下载
- 积分：1
-
源程序
说明： 基于labview的振动信号采集与分析的一段编程(A program of vibration signal acquisition and analysis based on Lab View)
- 2020-05-15 03:46:29下载
- 积分：1
-
1224电压测试项目源代码V3
说明： NI USB-6001电压/阻测试项目源代码（labview2017）
1，使用io触发，自动扫描io上升沿，输入io可选。
2，使用差分方式采样，双通道同时采样，采样数据实时显示。
3，可手动触发采样，采样率，采样数，测试周期可自定义。
4，可保存控件值，运行程序自动加载上次保存的控件值。
5，数据保存到.xls表格，每天新建以年-月-天命名的文件，每个月创建一个文件夹存放数据。
6，测试结果通过USB-6001自带io输出。
真实项目应用源代码!(1. Use IO trigger to scan the rising edge of IO automatically. Input IO is optional.
2. Sampling by differential mode, sampling by two channels at the same time, and real-time display of sampled data.
3. Sampling can be triggered manually. Sampling rate, sampling number and testing period can be defined.
4. The control value can be saved, and the last saved control value can be automatically loaded by the running program.
5. Data is saved to the. xls table. New files named year-month-day are created every day, and a folder is created every month to store data.
6. The test results are output by USB-6001 with io.
Real Project Application Source Code!)
- 2018-12-25 14:14:11下载
- 积分：1
-
Subpanelzairu
LabVIEW环境下动态载入技术，个人编写的，在8.5版本下可以运行，很好的！(LabVIEW environment, dynamic loading technology, personal written version may be run at 8.5, very good!)
- 2010-06-01 11:25:37下载
- 积分：1
