CG_Client_Source

UDT（UDP-based Data Transfer Protocol，简称UDT）是一种互联网数据传输协议。UDT建于UDP之上，并引入新的拥塞控制和数据可靠性控制机制。UDT是面向连接的双向的应用层协议。它同时支持可靠的数据流传输和部分可靠的数据报传输。 (UDT is a reliable UDP based application level data transport protocol for distributed data intensive applications over wide area high-speed networks. UDT uses UDP to transfer bulk data with its own reliability control and congestion control mechanisms. The new protocol can transfer data at a much higher speed than TCP does. UDT is also a highly configurable framework that can accommodate various congestion control algorithms)

回声消除代码实例，具有一定的参考价值，可以下载使用。(voice aec code example ,will be valuable to you work if you download it)

基于Winpcap的网络数据包抓取.开发环境VS2013(network packet capture based on Winpcap . Development environment: VS2013)

中频感应加热以其加热效率高、速度快，可控性好及易于实现机械化、自动化等优点，已在熔炼、铸造、弯管、热锻、焊接和表面热处理等行业得到广泛的应用。 本设计根据设计任务进行了方案设计，设计了相应的硬件电路，研制了20KW中频感应加热电源。 本设计中感应加热电源采用IGBT作为开关器件，可工作在10 Hz～10 kHz频段。它由整流器、滤波器、和逆变器组成。整流器采用不可控三相全桥式整流电路。滤波器采用两个电解电容和一个电感组成Ⅱ型滤波器滤波和无源功率因数校正。逆变器主要由PWM控制器SG3525A控制四个IGBT的开通和关断，实现DC-AC的转换。 设计中采用的芯片主要是PWM控制器SG3525A和光耦合驱动电路HCPL-316J。设计过程中程充分利用了SG3525A的控制性能，具有宽的可调工作频率，死区时间可调，具有输入欠电压锁定功能和双路输出电流。由于HCPL-316J具有快的开关速度（500ns），光隔离，故障状态反馈，可配置自动复位、自动关闭等功能，所以选择其作为IGBT的驱动。 对原理样机的调试结果表明，所完成的设计实现了设计任务规定的基本功能。此外，为了满足不同器件对功率需要的要求，设计了功率可调。这部分超出了设计任务书规定的任务。(induction heating with high heating efficiency, speed and good controllability and easy to mechanization. the advantages of automation, in melting, casting, bending, forging, welding and surface heat treatment and other industries have been widely employed. According to the design tasks for the design of the program design, design corresponding to the hardware circuit, Development of 20 KW induction heating power. The design of induction heating power IGBT used as a switching device, which can work in 10 Hz- 10 kHz frequency band. It consists of rectifier, filter, and the inverter components. Controlled Rectifier not use the entire three-phase bridge rectifier circuit. 2 filter used an electrolytic capacitor and inductor components II-type filter and passive PFC. Inverter mainly by the PW)

用来控制网卡的源码，可以列出机器中所有的网卡，并可实现禁用和启用网卡(card used to control the source, a list of all the machines card and can achieve banned and the opening of NIC)

显示和修改网卡地址和网关.DNS Visual Basic编程.(Display and modify the network card address and gateway. DNS Visual Basic programming.)

这是一个用vc++编写的，用以截获以太网数据的代码。(This is a used vc++ Prepared for Ethernet data intercepted code.)

说明：  根据域名获得IP地址列表 根据域名获得IP地址列表(under the name list of IP addresses under the domain of IP address list)

UDP 接收数据类，里面有个接收UDP数据的线程。 我自己使用的，可靠的，已经编成DLL了，其中有些解析二进制流的代码，可以不看。(udp socket program , focus on recieve udp data.)

屏幕录制或广播，选择执行的区域或某个窗口或应用程序，使其凸显(Screen recording or broadcast, the area or a window or application execution, highlights)