general_freqresponse_solution

使用块匹配法的三步搜索对视频中的两帧图象进行预测编码(Use block matching method for video of the three-step searching two frames image forecast coding)

说明：  NCO模块的设计函数，用于产生正弦、余弦信号(It s a design functions about NCO module ，which is used for generating sine, cosine signal)

it gives the matlab simulink for the statcom with the battery energy source system

这个程序详细说明了怎么用极坐标画天线方向图(This procedure specifies how to use the antenna pattern in polar coordinates Videos)

离散论域模糊控制表的离线计算.已知单变量两维输入，一维输出模糊控制器，其两维输入为E，EC，一维输出为I，论域均为E，EC，I∈{-6，-5，-4，-3，-2，-1，0，1，2，3，4，5，6}，E的论域划分为{NB，NM，NS，NZ，PZ，PS，PM，PB}，共8个模糊子集(Discrete domain of fuzzy control table offline computing. Known univariate two-dimensional input, one-dimensional output fuzzy controller, the two-dimensional input of E, EC, one-dimensional output as I, on the field are E, EC, I ∈ {-6,-5,-4,-3,-2,-1,0,1,2,3,4,5,6}, E of the domain is divided into {NB, NM, NS, NZ, PZ , PS, PM, PB}, a total of eight fuzzy subset)

说明：  matlab FIR 底通和带通滤波器和IIR 底通和带通滤波器完整程序(Matlab fir bottom pass and band-pass filter and IIR bottom pass and band-pass filter complete program)

In this interface, you can control the sources (type, frequency, length, represented points), the mixture (elements of the mixing matrix and nonlinears functions in the post nonlinears cases), the different parameters of noise, the separating algorithm (choice between two algorithms and associated parameters) and the parameters of denoising.(All the algorithms simulated in this package have been designed by Massoud BABAIE-ZADEH during his PhD thesis, prepared in the Images and Signals Laboratory (LIS) of Institut National Polytechnique de Grenoble (INPG), under the supervision of Christian JUTTEN.)

利用雷达方程，分析信噪比在三种不同的脉冲下与检测目标距离的关系，从而得出相应的结果。(By the radar equation, analysis of signal to noise ratio and the relationship between the distance of the detection target in the three different pulses, so as to draw the corresponding results.)

由于显卡或者显示器的原因会出现实际输出的图像在亮度上有偏差，而Gamma曲线矫正就是通过一定的方法来矫正图像的这种偏差的方法.(Or because of the graphics display image will appear in the actual brightness of the output deviation, the Gamma correction curve is corrected by a certain method to the method of this bias image.)

说明：  数字信号处理设计与仿真分析 (1)建立两个模拟信号的数学模型 sa1(t)和 sa2(t)， 其中 sa1(t)是有用信号， sa2(t)是干 扰信号。 两个信号的中心频率、信号带宽等参数由学生自己选定，要求两个信号的频谱不重 叠， sa2(t)的幅度比 sa1(t)的幅度高 20dB， 两个信号时域叠加得到合成信号 xa(t)， 即 xa(t)= sa1(t)+ sa2(t) 设计计算机程序仿真产生 sa1(t)、 sa2(t)、 xa(t)信号， 分别画出三个模拟信号的时域波 形和频谱图；(Establish two mathematical models of analog signals sa1(t) and SA2 (t), where SA1 (t) is the useful signal and SA2 (t) is the dry signal Interference signals.)