登录
首页 » Asm » BAT500

BAT500

于 2015-10-29 发布 文件大小:2KB
0 241
下载积分: 1 下载次数: 8

代码说明:

  艾默生串口驱动打印机,带有BAT500协议(BAT500 printer,protocol of BAT500)

文件列表:

BAT500.c,7997,2015-10-12
BAT500.h,283,2015-10-12

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • SiemensS7-200communicationset-upprocess
    西门子S7-200 与opc软件KEPServerEx的 通讯设置过程(Siemens S7-200 communication set-up process)
    2010-09-16 12:16:40下载
    积分:1
  • can232
    给出了基于MFC的can232接口的调试程序(MFC-can232 given based debugger interface)
    2010-12-03 17:30:41下载
    积分:1
  • serial_port_send-_data
    本文件相似的说明了串口发送数据的全部过程。(This document describes the entire process similar to the serial port to send data.)
    2013-12-17 13:24:42下载
    积分:1
  • Projects
    串口上位机,停车位管理,采用C++ Builder(PC serial port, parking management)
    2015-05-31 15:58:34下载
    积分:1
  • ser
    说明:  串口通信高级编程提供了一个能够进行串口通信的类,能够方便地进行各种数据通信。 由于本程序设计到硬件编程,因此,如果读者的串口通信设备 没有连接好,可能会有问题 (Serial communication provides a high-level programming to carry out the type of serial communication, the ability to easily carry out a variety of data communications. Since the hardware design to programming, so if the reader' s serial communications equipment is not connected well, there may be some problems)
    2009-08-18 16:49:04下载
    积分:1
  • myShowData
    C#编写的数据显示程序,曲线显示,可以手动调整,也可以自动加载,数据是通过串口收到的数据,和前一个程序myDataCollect.zip配套使用!(Data written in C# program, the curve shows, you can manually adjust, you can also automatically load the data received through the serial data, and the former supporting the use of a program myDataCollect.zip!)
    2011-04-22 12:18:09下载
    积分:1
  • serial
    串口调试,visual basic撰写,可以发送包括word格式,excel格式,text格式等文件(Serial debugging, visual basic writing, including word format can be sent, excel format, text format file)
    2014-05-25 09:15:13下载
    积分:1
  • RoboMasters
    大僵云台设计资料,云台控制讲解,大僵内部培训资料,云台控制结构图(DJI GIMBAL )
    2015-07-21 22:32:25下载
    积分:1
  • protol
    自己编写的变异的modbus,先分享给大家(the modbus by myself,now give all)
    2019-06-01 23:36:15下载
    积分:1
  • Digital_communication_programm
    说明:  数控程序传输,主要是三个程序,KND及GSK990m传输软件,Sercom,hmcadcam_Dnc(NC program transmission, there are three main procedures GSK990m KND and transmission software, Sercom, hmcadcam_Dnc)
    2006-03-07 08:36:41下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载