Laplacian_Eigenmaps

another progaram that has been in matlab

说明：  两种对二阶系统进行参数辨识的最小二乘算法，一种可以直接得到输入输出之间的传递函数，一种可以解出线性的差分方程各系数，再反解得到传递函数。附带的一个二阶系统的模型，可以自行下载导入输入输出数据进行试验。(Two kinds of least square algorithm for parameter identification of second-order system, one can directly get the transfer function between input and output, the other can solve the coefficients of linear difference equation, and then get the transfer function by inverse solution. The attached model of a second-order system can download the input and output data for test.)

doa估计的各类经典算法, 适合信号方位估计的各类参考(doa estimation algorithm classic, simple DOA estimation algorithm, algorithm)

无线定位基本算法 TDOA AOA TOA(Wireless location algorithm on TDOA the AOA TOA)

This is a very good book on Robust optimization that covers all the essentials of robust optimization.

Set-based stochastic optimization for evolving instinct-learning balance

Bayesian Model Selection

说明：  根据风速公式在SIMULINK环境中搭建的渐近风速的模型，可运行。(According to the formula， in the SIMULINK environment wind asymptotic velocity of the model is builded,and it can run)

Soft Acoustic Mordern using matlab. Wireless Acoustic mordern simulation using coomputer build-in sound card.

1） 借助MATLAB画出误差性能曲面和误差性能曲面的等值曲线； 2） 写出最陡下降法， LMS算法的计算公式（ ）； 3） 用MATLAB产生方差为0.05,均值为0白噪音S(n)，并画出其中一次实现的波形图； 4） 根据2）中的公式，并利用3）中产生的S(n)，在1）中的误差性能曲面的等值曲线上叠加画出采用最陡下降法， LMS法时H(n)的在叠代过程中的轨迹曲线。 5）用MATLAB计算并画出LMS法时 随时间n的变化曲线（对 应S(n)的某一次的一次实现）和e(n)波形；某一次实现的结果并不能从统计的角度反映实验的结果的正确性，为得到具有统计特性的实验结果，可用足够多次的实验结果的平均值作为实验的结果。用MATLAB计算并画出LMS法时J(n)的100次实验结果的平均值随时间n的变化曲线。 6）用MATLAB计算并在1）中的误差性能曲面的等值曲线上叠加画出LMS法时100次实验中的H(n)的平均值的轨迹曲线； 7）对以上实验结果给出一些你认为有价值的讨论。 （在实验中n=1,,…..N,N的取值根据实验情况确定，一般选取足够大以使算法达到基本收敛，本题作业以电子文档PDF格式提供） (1) With MATLAB to draw the contours of the error performance surface and error performance surface 2) Write down the steepest descent method, the LMS algorithm formula () 3) using MATLAB variance 0.05, mean 0 white noise S (n), and draw one to achieve the waveform diagram 4) According to the formula 2), and using 3) S (n) produced in 1), the error performance of the contours of the surfaces superimposed on draw using the steepest descent method, the LMS method is H (n) in the iterative process in the trajectory curve. 5) curve to calculate and draw the LMS method using MATLAB with time n (time corresponding to the S (n) of a first implementation) and e (n) waveform reflect a certain time to achieve results not from a statistical point of experiment the correctness of the results obtained with the experimental results of the statistical properties of the available sufficient times the average of the experimental results as a result of the experiment. Calculate and draw the LMS m)