登录
首页 » matlab » xunhuansaomiao08

xunhuansaomiao08

于 2015-08-24 发布 文件大小:3KB
0 392
下载积分: 1 下载次数: 45

代码说明:

  采用内螺旋算法编写的清洁机器人路径规划程序,将房间抽象为栅格矩阵(Spiral algorithm written using cleaning robot path planning program, the room abstract grid matrix)

文件列表:

xunhuansaomiao08.m,16536,2015-08-23

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • Djuric---MCiSP
    数字信号处理中的基于Monte Carlo的方法(Monte Carlo-based methods in signal processing)
    2014-01-04 23:10:17下载
    积分:1
  • gausjord
    Gauss-Jordan routine, single RHS
    2010-11-16 17:50:54下载
    积分:1
  • 12
    说明:  最大信噪比盲源分离算法 该算法参考文为 给予最大信噪比的盲源分离算法 《计算机仿真》 2006.2(Maximum signal to noise ratio Blind source separation)
    2011-05-09 16:46:16下载
    积分:1
  • 04408441
    研究脑电的经典文章,国外大牛写的,值得推荐,研究脑电信号处理的方法(EEG studies classic article, written by Daniel abroad, it is recommended to study the EEG signal processing methods)
    2013-08-11 10:58:02下载
    积分:1
  • Centroid
    WSN 质心定位算法 Centorid Algorithm 加经典参考文献 A: 如果接受节点接收到的包数目与发送节点发送的包数目的比值大于CM_threshold,则这两个节点视为邻居节点 未知节点利用邻居锚节点进行定位,没有邻居锚节点的未知节点无法定位。 B: 如果接受节点接收到的包数目与发送节点发送的包数目的比值大于CM_threshold,则这两个节点视为邻居节点 未知节点一旦被定位就充当起锚节点的功能,向周围邻居发送自己的估计坐标信息 未知节点把已经定位的未知节点与锚节点同等对待 C: 如果接受节点接收到的包数目与发送节点发送的包数目的比值大于CM_threshold,则这两个节点视为邻居节点 有邻居锚节点的未知节点只利用邻居锚节点进行定位,没有邻居锚节点的未知节点才利用已经定位了的邻居未知节点进行定位。(WSN centroid localization algorithm Centorid Algorithm A: If you accept the received packet node number and the number of packets sent by the sending node ratio greater than CM_threshold, then these two nodes as neighbors Unknown node using the neighbor anchor nodes to locate, no neighbors anchor nodes and unknown nodes can not be located. B:   If you accept the received packet node number and the number of packets sent by the sending node ratio greater than CM_threshold, then these two nodes as neighbors Unknown nodes are positioned on as soon as the function of anchor nodes to send their neighbors estimated coordinate information Unknown unknown node to node already positioned anchor nodes treated equally C: If you accept the received packet node number and the number of packets sent by the sending node ratio greater than CM_threshold, then these two nodes as neighbors Of the unknown neighbor anchor node the neighbor nodes are only positioned anchor nodes, )
    2013-08-31 19:13:47下载
    积分:1
  • nonlinear-system-model
    以m 文件编写S-Function函数,实现以下Bell 和 Astrom(1987) 关于某160MW燃油机组特性的非线性系统的模型(M file write S-Function function implement following Bell and Astrom (1987) model of the nonlinear system on the characteristics of a 160MW fuel unit)
    2012-11-19 10:09:11下载
    积分:1
  • Sequential_Detection
    已知方差的高斯随机信号的序贯检测:给出了H0和H1假设下理论推导得到的序贯检测平均样本数的曲线,以及仿真得到的序贯检测平均样本数的曲线,理论结果和仿真结果较为吻合。(Sequential detection of known variance Gaussian random signals: H0 and H1 are given under the assumption that the theoretical derivation curve sequential detect the average number of samples obtained, and curve sequential simulation to detect the average number of samples obtained theoretical results and simulation The results are more consistent.)
    2020-10-10 14:37:34下载
    积分:1
  • liu_ks02
    最大似然(ML)准则和最大后验概率(MAP)准则,多机电力系统仿真及其潮流计算,采用的是脉冲对消法。( Maximum Likelihood (ML) criteria and maximum a posteriori (MAP) criterion, Multi-machine power system simulation and flow calculation, It uses a pulse of consumer law.)
    2017-05-15 11:27:23下载
    积分:1
  • FFT
    说明:  FFT频域滤波,用于图像进行fft频域滤波变换,很实用的小程序。(failed to translate)
    2011-04-17 15:53:17下载
    积分:1
  • Optimize
    MATLAB 6_5 辅助优化计算与设计 1、文件命名说明 a)文件夹“第1章”中的文件对应书中第1章的例程,其他以此类推; b) 文件名exampleX1_X2.m:对应例程X1_X2 例如:example2_1表示例程2_1. 2、注意 为了方便起见,书中的每一个例程存为一个文件;而有些例程中将其调用的函数文件也放在这个例程文件中,所以读者在运行光盘中的例程文件时注意这一点,如果是这样的例程文件应该将其调用的函数文件分离出来另存为一个文件。(MATLAB 6_5 Auxiliary and Design Optimization 1, Note document naming a) folder "Chapter 1" in the document corresponding book Chapter 1 of the routines, other analogy; b) Name exampleX1_X2.m : X1_X2 corresponding routines such as : example2_1 said two compression routines. 2, the attention for the sake of convenience, Each book deposit for a routine one; Some routines will call a function of its documents on the routines document, Therefore, the reader is running the routines CD document to this point, If this is the routine document should be called to separate the function documents saved as a file.)
    2006-11-23 17:07:55下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载