sdr_normal

系列语音温度控制器适用于别墅、公寓、办公楼及工业商业等,用于控制中央空调、水采暖、电采暖的恒温控制,达到调节室内温度保持恒温及舒适节能的目的。(The series voice temperature controller suitable for villas, apartments, office buildings and industrial commercial, used to control central air conditioning, water heating, electric heating thermostat control, reach adjust the indoor temperature to maintain constant temperature and comfort energy saving purposes)

说明：  LCD12864 ST7567驱动程序 HAL库(LCD12864 sT7567 driver HAL Library)

说明：  利用STM32F103来实现旋转LED功能，显示汉字(Realize the function of rotating LED)

energia的一个无线模块库，新手上路，各位大佬多帮衬。(A wireless module library of Energia)

STM32作为主控芯片，72Mhz，利用DMA+PWM实现驱动WS2812，创建16个并行800kBit / s数据流的想法如下： 使用定时器每1.25us创建一个800kHz的时基和一个DMA请求。 使用2个比较模块在低位时间（350ns）和高位时间（700ns）下创建DMA请求 1.25us DMA请求将GPIO端口的所有位设置为高电平 350ns DMA请求将数据从帧缓冲区传输到GPIO端口。如果该位为0，GPIO引脚将变为低电平，否则将保持高电平。 700ns DMA请求将所有GPIO引脚设置为低电平。 重复步骤1到3，直到发送所有位。 这产生脉冲周期为1.25us，脉冲宽度为350ns或700ns的脉冲流，具体取决于脉冲表示的位值，通过DMA将数据传输到GPIO端口意味着每16个LED每位需要一个字（两个字节）。每个LED 24位，每16个LED 24个字（48个字节）。(The idea to create 16 parallel 800kBit/s data streams is the following: Use a Timer to create an 800kHz time base and a DMA request every 1.25us. Use 2 compare modules to create DMA requests at the low bit time (350ns) and the high bit time (700ns) The 1.25us DMA request sets all bits of the GPIO port high The 350ns DMA request transfers the data from the frame buffer to the GPIO port. If the bit is a 0, the GPIO pin will go low, otherwise it will stay high. The 700ns DMA request sets all GPIO pins low. Repeat steps 1 to 3 until all bits have been transmitted. This creates a stream of pulses with a pulse period of 1.25us and a pulse width of either 350ns or 700ns depending on the bit value the pulse represents. Transferring the data via DMA to the GPIO port means that per 16 LEDs one half word (two bytes) is needed per bit. At 24 bits per LED that makes 24 half words (48 bytes) per 16 LEDs.)

8个单片机小程序，对串口、中断的学习很好理解。(8 SCM applet, the serial interrupt learning well understood.)

8051 练习项目，包含串口、定时器、红外遥控、LCD1602、SMI串行总线读写等功能。(8051 exercise items, including serial port, timer, infrared remote control, LCD1602, SMI serial bus reading and writing functions.)

超声波测距，能够实现汽车防撞系统超声波的测距，完全由51单片机控制(Ultrasonic Ranging)

PZEM-014模块检测电压、电流、电功率、电能等信息，在LCD1602上显示(PZEM-014 module detects voltage, current, power, electric energy and other information, which is displayed on LCD1602.)

说明：  本程序用于进行声音的传输、编码、解码、播放功能。(This procedure is used for voice transmission, encoding, decoding, playback function.)