opnet

第1章　用于可靠数字传输和存储的编码 第2章　代数引论 第3章　线性分组码 第4章　重要的线性分组吗 第5章　循环码 第6章　二进制BCH码 第7章　非二进制BCH码、RS码及其译码算法 第8章　大数逻辑可译码有限几何码 第9章　线性分组码的网络 第10章　基于可靠性的线性分组码软判决译码算法 第11章　卷积码 第12章　卷积码的最优译码 第13章　卷积码的次优译码 第14章　基于网络的软判决译码算法 第15章　级联编码、码分解与多阶段译码 第16章　Turbo编码　 第17章　低密度单奇偶校验码 第18章　网络编码调制 第19章　分组编码调制 第20章　纠突发错误码 第21章　纠突发错误卷积码 第22章　自动请求重传（ARQ）策略 附录A　伽罗华域的表 附录B　GF（2m）中元素的最小多项式 附录C　长度至2　10-1的二进制本原BCH码的生成多项式 9.6 卷积码 (Error-controlled coding techniques are used to detect and/or correct errors that occur in the message transmission in a digital communications system. Wireless personal channels used by mobile communications systems and storage systems for digital multimedia data all require the implementation of error control coding methods. Demonstrating the role of coding in communication and data storage system design, this text illustrates the correct use of codes and the selection of the right code parameters. Relevant decoding techniques and their implementation are discussed in detail. Providing communication systems engineers and students with guidance in the application of error-control coding, this book emphasizes the fundamental concepts of coding theory while minimising the use of mathematical tools. * Reader-friendly approach ti coding in communication systems providing examples of encoding and decoding, information theory and criteria for code selection * Thorogh descriptions of releva)

说明：  turbo码的c语言程序，使用c语言来完成整个turbo码的编解码过程，并且程序后附带比较详细的解释(turbo code c language program, use c language to complete the entire turbo code codec process and procedures attached to explain it in more detail)

给出了OFDM在卫星通信中的系统框图并 在Simulink中仿真实现，利用改进的CMA恒模算法进行盲均衡处理，来去除时变卫星信道对信号的影响,基于4阶累积量的方法 将OFDM信号与其他调制类型信号区分开来(OFDM is given in the satellite communication system block diagram and Simulation in Simulink using the modified constant modulus algorithm CMA for blind equalization, to remove the time-varying satellite channel on the signals, based on 4-order cumulant method OFDM signals and other types of signal modulation to distinguish)

The whole reuse mode of LTE is simulated systematically, which is a good learning program.

这是一个基于OPtisystem下的对于8PSK信号的仿真，可用于通信工程作业的一般仿真系统。(This is a simulation system of 8PSK signal based on OPtisystem, which can be used in general simulation system of communication engineering operation)

在瑞丽衰落 =信道下，对信号进行qPSK调制(qpsk for relaygh channel)

简单实现基于加权分数傅里叶变换的混合载波系统(Simple Implementation of Hybrid Carrier System Based on Weighted Fractional Fourier Transform)

说明：  matlab的bpsk，qpsk，msk，qam打包下载，不是自带的程序函数。按照通信框图做的程序(MATLAB，bpsk，qpsk，msk，qam)

采用labview编写的I2C通信程序，几乎可以通用的喔(prepared by the I2C communications procedures, almost generic oh)

说明：  5. 在三条径的瑞利信道中，对于直接序列扩频： (1) 请设计DS-CDMA一种具体的码分导引辅助的信道估计方法，接收机分别采用等均益合并、最大比合并。用Simulink进行仿真，画出比特信噪比与信道估计均方误差的关系曲线和比特信噪比与误码率的关系曲线。 (2) 设频率已经同步，请设计DS-CDMA一种具体的单停顿滑动相关时间同步方法，用Simulink进行仿真，画出比特信噪比与捕获概率的关系曲线。 (3) 设时间已经同步，请设计DS-CDMA一种具体的频率同步方法，用Simulink进行仿真，画出比特信噪比与频率同步误差的关系曲线。(5. In three-path Rayleigh channel, for direct sequence spread spectrum: (1) please design a specific code division navigation aided channel estimation method for ds-cdma, and adopt equal-beneficial combination and maximum ratio combination for receivers respectively.Simulink is used to simulate and draw the relationship curve between bit SNR and channel estimation mean square error and the relationship curve between bit SNR and bit error rate. (2) assuming that the frequency has been synchronized, please design a specific single-stop sliding correlation time synchronization method ds-cdma, Simulink simulation, draw the relationship between the bit SNR and the acquisition probability curve. (3) if the time has been synchronized, please design a specific frequency synchronization method ds-cdma, Simulink simulation, draw the relationship between the bit SNR and frequency synchronization error curve.)