Matlab

复杂网络中几种常见网络的生成程序。详细说明了生成机理，对于初学者帮助较大。(Complex network of several common network formation process. Detailed description of the formation mechanism, for beginners to help more.)

说明：  蚁群算法解决TSP问题，可以高速运行，附有详细注释(Ant colony algorithm to solve TSP problem, you can run at high speed, with detailed notes)

带有恶化时间的作业车间调度问题matlab 程序(Job shop scheduling problem with time to progression matlab program)

经验模态分解程序集，一类可以有效进行信号分段以及分析和处理的源代码。(Empirical mode decomposition procedure)

常用的MATLAB图像压缩编码，通过matlab实现，其中包含了DM编码、变换编码（FFT和DCT）、算术编码、行程编码、JZOTch编码、线性预测编码和一个近似的NHzjZsp编码过程。本人通过MATLAB编码效率很高。 (Commonly used MATLAB image compression coding, through matlab implementation, which includes the DM coding, transform coding (FFT and DCT), arithmetic coding, run length coding, JZOTch coding, linear predictive coding and an approximate NHzjZsp encoding process. I have a high coding efficiency by MATLAB. )

小波变换进行变速箱故障诊断 首先将s1和s2信号时域谱（s1代表维修前的振动信号，s2代表维修后的振动信号），画出来进行对比，会发现s1信号的振动幅值会比较高；然后对s1和s2分别进行小波分解并画出各层的时域谱，只对比s1和s2分后的最高时域谱，s2更加的具有周期性，且幅值较小，s2周期性不够明显，且振动过于密集。分析完时域谱后开始分析频谱，首先对原信号s1和s2fft转换，得到频谱图，如图，然后再对小波分析后高频部分进行fft转换，做出频谱图。对比后我们发现，在f 2375HZ出（也就是齿轮的啮合频率），s1信号频谱幅值会有急剧的升高，然后，其谐波的幅值也会增大。所以可以推断出该维修前的增速箱的齿轮可能出现问题。(Gearbox fault diagnosis based on wavelet transform s1 and s2 first time domain signal spectrum (s1 behalf of the vibration signal before maintenance, vibration signal s2 representative of repaired), drawn comparison, you will find a signal s1 vibration amplitude will be higher then s1 and s2 respectively wavelet decomposition and draw the layers of time-domain spectrum to only a maximum time domain spectroscopy s1 and s2 points after, s2 is more cyclical and smaller magnitude, s2 cyclical enough obviously, and the vibration is too dense. End domain spectral analysis after the beginning of the spectrum analysis, the first of the original signal s1 and s2fft conversion to give the spectrum, as shown, and then after the high frequency part of wavelet analysis fft transformation to make spectrum. We found that after the comparison, at f 2375HZ out (i.e. the gear mesh frequency), there will be a sharp increase in the amplitude spectrum of the signal s1, and then, the amplitude of the ha)

Buck peak current mode control

计算多重分形非趋势波动分析matlab程序,能量谱分析计算,GSM中GMSK调制信号的产生。( Calculation multifractal detrended fluctuation analysis matlab program, Energy spectrum analysis and calculation, GSM is GMSK modulation signal generation.)

％File: c9_estimatepi.m ％有5个pi的估计，每一个都是基于500次重复随机试验，所得的pi的五个估计值用以下向量表示 ％pi的估计值=[3.0960 3.0720 2.9920 3.1600 3.0480] ％如果对5个结果进平均，则pi的估计值=3.0736,这样的结果等价于2500次的试验结果。( File: c9_estimatepi.m have 5 pi estimates are based on a randomized trial to repeat 500 times the income of the five estimated value of pi with the following vector, said the estimated value of pi = [3.0960 3.0720 2.9920 3.1600 3.0480] if the results into an average of 5, then the estimated value of pi = 3.0736, so the result is equivalent to 2500 times the test results.)

一个实例搞定MATLAB界面编程,极易上手(An instance to get the the MATLAB programming interface, easy to use)