登录
首页 » matlab » DVB-T

DVB-T

于 2015-07-14 发布 文件大小:1061KB
0 220
下载积分: 1 下载次数: 23

代码说明:

  DVB-T Matlap simulation using OFDM

文件列表:

DVB-T.mat,1122888,2015-01-28

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 5-references
    这是5个有关Kinect face recognition的paper,介绍了kinect的相关知识和人脸识别的一些知识,很有帮助。(face recognition with 3D kinect.)
    2013-07-09 22:16:16下载
    积分:1
  • Face_001
    基于形状特征的人脸分类研究,文中介绍了将模糊聚类方法用于人脸分类。 (based on the shape of the human face classification, the paper introduced the fuzzy clustering method for human face classification.)
    2006-12-25 20:03:20下载
    积分:1
  • Empirical_with_Delay
    Empirical Model process orde 1
    2010-11-09 10:38:26下载
    积分:1
  • sanshe1
    c++ and matlab 散射电流可视化、球体(c++ and matlabScattering current visualization, sphere )
    2012-03-30 11:15:00下载
    积分:1
  • MM1Queue_v2
    Monte carlo simulation of an M/M/1 queue, with plots of the convergence of average waiting time, queue length, etc.
    2011-09-19 10:56:42下载
    积分:1
  • BPSK
    一个关于BPSK误码率仿真的程序,其中包括信号产生,加入高斯白噪声,和误码率计算!(One on BPSK BER simulation procedures, including the signal generated by adding Gaussian white noise, and bit error rate!)
    2009-12-14 19:25:39下载
    积分:1
  • mulNewton
    非线性曲线拟合使用maltab牛顿高斯迭代,并用初始值(Nonlinear curve fitting useing Maltab Newton gaussian iteration need Initial value )
    2013-01-02 11:50:41下载
    积分:1
  • MATLAB_scheler
    GPS Scheler Period Simulation at MATLAB
    2015-03-12 11:07:33下载
    积分:1
  • QAMXIANGP
    本程序仿真了16QAM信号的载波相偏估计的HOS算法,整个算法实现分为(1)模拟发送端发送16QAM信号;(2)加入相偏来模拟通过信道后有相偏的测试信号;(3)利用HOS算法进行相偏估计与纠正;(4)输出星座图。(This procedure simulated a 16QAM signal carrier phase offset estimate of the HOS algorithm, the algorithm is divided into (1) analog transmitter to send 16QAM signal (2) by the inclusion of partial to simulate the channel after the phase offset of the test signal (3 ) algorithm using HOS phase offset estimate and correction (4) output constellation.)
    2010-08-31 21:06:21下载
    积分:1
  • FIRshuzilvboqi
    说明:  一个FIR数字低通滤波器的设计,在CCS设计之前先在MATLAB中进行仿真,观察一下效果。并得到参数,然后再导入CCS中,用CCS实现FIR滤波器的设计。(A low-pass FIR digital filter design, design before the CCS in the MATLAB simulation and observe the results. And are parameters, and then import the CCS, the CCS to achieve with FIR filter design.)
    2011-03-18 11:01:38下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载